Re: [avr-chat] avrdude atmelice

[Andy Rea]

I need to use the JTAG programmer as i’m using and only have access to the JTAG 
port of the mega1280, however just for bemusement changing to that type gives 
the same result

D:\svn\LC500TestRigProgrammer\BinaryFiles>avrdude -c atmelice_isp -p m1280  -v 
-v -v -v

avrdude: Version 6.1, compiled on Mar 13 2014 at 00:09:49
         Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
         Copyright (c) 2007-2014 Joerg Wunsch

         System wide configuration file is 
"D:\svn\LC500TestRigProgrammer\BinaryFiles\avrdude.conf"

         Using Port                    : usb
         Using Programmer              : atmelice_isp
avrdude: stk500v2_jtag3_open()
avrdude: usbdev_open(): Found Atmel-ICE Data Gateway, serno: J41800025592
avrdude: jtag3_getsync()
avrdude: Sending sign-on command:
avrdude: jtag3_send(): sending 3 bytes
avrdude: usbdev_send(): wrote -22 out of 7 bytes, err =
avrdude: jtag3_send(): failed to send command to serial port
avrdude: jtag3_recv():
avrdude: usbdev_recv_frame(): usb_bulk_read():
avrdude: jtag3_recv(): Timeout receiving packet

avrdude: sign-on command: timeout/error communicating with programmer (status 
-1)
avrdude: failed to sync with the JTAGICE3 in ISP mode

avrdude done.  Thank you.

From: Andrew Chin [mailto:address@hidden 
Sent: 20 May 2015 14:24
To: Andy Rea
Subject: Re: [avr-chat] avrdude atmelice

I have got it talking to arduinos. I do not remember off the top of my head, 
but you need the latest avrdude downloaded, which i believe you have. Then it 
required you to search in its tree for the correct TAG. I think it is 
"atmelice_isp", not "atmelice". I made the same mistake.

On Wed, May 20, 2015 at 8:10 AM, Andy Rea <address@hidden> wrote:
Does anyone have avrdude working with the atmel ice?
I added the libusb filter ( libusb version 1.2.6 ) and this is the output
 
I know I’ve avrdude with the USBtiny programmers before with no problem
 
The Atmel-ice firmware version is 1.16 ( latest as far as I can tell )
 
I know I’m not actually asking it to do anything but it appears not to even be 
talking to the box once it has found and opened it.
 
below is the output:
 
any comments would be appreciated
 
thanks
 
Andy
 
D:\svn\LC500TestRigProgrammer\BinaryFiles>avrdude -c atmelice -p m1280  -v -v 
-v -v -v
 
avrdude: Version 6.1, compiled on Mar 13 2014 at 00:09:49
         Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
         Copyright (c) 2007-2014 Joerg Wunsch
 
         System wide configuration file is 
"D:\svn\LC500TestRigProgrammer\BinaryFiles\avrdude.conf"
 
         Using Port                    : usb
         Using Programmer              : atmelice
avrdude: jtag3_open()
avrdude: usbdev_open(): Found Atmel-ICE Data Gateway, serno: J41800025592
avrdude: jtag3_getsync()
avrdude: Sending sign-on command:
avrdude: jtag3_send(): sending 3 bytes
avrdude: usbdev_send(): wrote -22 out of 7 bytes, err =
avrdude: jtag3_send(): failed to send command to serial port
avrdude: jtag3_recv():
avrdude: usbdev_recv_frame(): usb_bulk_read():
avrdude: jtag3_recv(): Timeout receiving packet
 
avrdude: sign-on command: timeout/error communicating with programmer (status 
-1)
 
avrdude done.  Thank you.

_______________________________________________
AVR-chat mailing list
address@hidden
https://lists.nongnu.org/mailman/listinfo/avr-chat