Re: [Bayonne-devel] Placing an outgoing call on an available trunk.

[Lachlan Ross]

Thanks Julien and to everyone who helped out on this one!
I have 30 channels on the card in my machine.
If I have in my conf:

------------------------
[trunks]
; Specify the name of additional trunk groups to load
groups =  outgoing

[outgoing-trunks]
trunks = 
0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22,23,24,25,26,27,28,29
-----------------------

Does this mean 0-29 are dedicated to outgoing calls only?
What impact does it have on my incoming calls?
Can incoming calls still come in on truncks 0-29?
I can then write the command 'start outgoing myScript' and it will grab 
an available trunk between 0-29 right?

Thanks again.

Lachlan


Julien Chavanton wrote:

> You must define the trunk in bayonne.conf
>
> Here is an example with 10 T1's, with E1's there is 30 channels not only
> 23.
>
> Then you can write the command "start trunk1 myScript" in bayonne.ctrl
> the bayonne FIFO.
>
>
> [trunks]
> ; Specify the name of additional trunk groups to load
> groups = trunk1 trunk2 trunk3 trunk4 trunk5 trunk6 trunk7 trunk8 trunk9
> trunk10
>
> [trunk1-trunks]
> trunks = 0,1,2,3,4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19,20,21,22
>
> [trunk2-trunks]
> trunks =
> 23,24,25,26,27,28,29,30,31,32,33,34,35,36,37,38,39,40,41,42,43,44,45
>
> [trunk3-trunks]
> trunks =
> 46,47,48,49,50,51,52,53,54,55,56,57,58,59,60,61,62,63,64,65,66,67,68
>
> [trunk4-trunks]
> trunks =
> 70,71,72,73,74,75,76,77,78,79,80,81,82,83,84,85,86,87,88,89,90,91,92
>
> [trunk5-trunks]
> trunks =
> 93,94,95,96,97,98,99,100,101,102,103,104,105,106,107,108,109,110,111,112
> ,113,114
>
> [trunk6-trunks]
> trunks =
> 115,116,117,118,119,120,121,122,123,124,125,126,127,128,129,130,131,132,
> 133,134,135,136,137
>
> [trunk7-trunks]
> trunks =
> 138,139,140,141,142,143,144,145,146,147,148,149,150,151,152,153,154,155,
> 156,157,158,159,160
>
> [trunk8-trunks]
> trunks =
> 161,162,163,164,165,166,167,168,169,170,171,172,173,174,175,176,177,178,
> 179,180,181,182,183
>
> [trunk9-trunks]
> trunks =
> 184,185,186,187,188,189,190,191,192,193,194,195,196,197,198,199,200,201,
> 202,203,204,205,206
>
> [trunk10-trunks]
> trunks =
> 207,208,209,210,211,212,213,214,215,216,217,218,219,220,221,222,223,224,
> 225,226,227,228,229
>
> -----Original Message-----
> From: address@hidden
> [mailto:address@hidden
> g] On Behalf Of Lachlan Ross
> Sent: May 2, 2005 9:48 PM
> To: Bayonne Devel Mailing List
> Subject: [Bayonne-devel] Placing an outgoing call on an available trunk.
>
> Hi Everyone,
>
> When using Bayonne to dial out, must you specify the trunk that the call
>
> goes out on?
> ie:
> bayonne --control start 1 myScript
>
> This sends the call out on trunk 1.  What happens if trunk 1 already has
>
> a call on it?
> Can you some how place an outgoing call and have it just find an 
> available trunk?
>
> Thanks for any ideas.
>
> Lachlan
>
>
>
>
> _______________________________________________
> Bayonne-devel mailing list
> address@hidden
> http://lists.gnu.org/mailman/listinfo/bayonne-devel
>