GNU Mach 1.3.99 AT386 boot: physical memory from 0x0 to 0x1ffec000 boot cr0 is 11 GNU Mach 1.3.99 AT386 boot: physical memory from 0x0 to 0x1ffec000 boot cr0 is 11 pcibios_init : BIOS32 Service Directory structure at 0xf92a0 pcibios_init : BIOS32 Service Directory entry at 0xf0f50 pcibios_init : PCI BIOS revision 2.10 entry at 0xf1150 Probing PCI hardware. hd0: ST340810A, 38166MB w/2048kB Cache, CHS=4865/255/63 hd2: Pioneer DVD-ROM ATAPIModel DVD-116 0122, ATAPI CDROM drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 ide1 at 0x170-0x177,0x376 on irq 15 Floppy drive(s): fd0 is 1.44M FDC 0 is a post-1991 82077 Failed initialization of WD-7000 SCSI card! EATA0: address 0x1f0 in use, skipping probe. EATA0: address 0x170 in use, skipping probe. ppa: Version 1.42 ppa: Probing port 03bc ppa: Probing port 0378 ppa: SPP port present ppa: ECP with a i byte FIFO present ppa: PS/2 bidirectional port present ppa: Failed Intel bug check. (Phony EPP in ECP) ppa: Probing port 0278 scsi : 0 hosts. scsi : detected total. rtl8139.c:v1.23a 8/24/2003 Donald Becker, becker@scyld.com. http://www.scyld.com/network/rtl8139.html eth0: RealTek RTL8139C Fast Ethernet at 0xa000, IRQ 11, 0:40:f4:55:56:9f. via-rhine.c:v1.16 7/22/2003 Written by Donald Becker http://www.scyld.com/network/via-rhine.html 0 3c515 cards found. eth1: D-Link DE-600 pocket adapter: not at I/O 0x378. D-Link DE-620 pocket adapter not identified in the printer port Partition check (DOS partitions): hd0: hd0s1 hd0s2 hd0s3 hd0s4 Linux PCMCIA Card Services 3.2.8 kernel build: 2.0.36 options: [pci] PCI routing table version 1.0 at 0xf1720 Intel ISA/PCI/CardBus PCIC probe: no bridges found. ds: no socket drivers loaded! xirc2ps_cs.c 1.31 1998/12/09 19:32:55 (dd9jn+kvh) com0: at atbus0, port = 3f8, spl = 6, pic = 4. (DOS COM1) com1: at atbus1, port = 2f8, spl = 6, pic = 3. (DOS COM2) lpr0: at atbus2, port = 378, spl = 6, pic = 7. module 0: /hurd/ext2fs.static --readonly --multiboot-command-line=${kernel-command-line} --host-priv-port=${host-port} --device-master-port=${device-port} --exec-server-task=${exec-task} -T typed ${root} $(task-create) $(task-resume) module 1: /lib/ld.so.1 /hurd/exec $(exec-task=task-create) 2 multiboot modules task loaded: /hurd/ext2fs.static --readonly --multiboot-command-line=/boot/gnumach.gz root=device:hd0s2 --host-priv-port=1 --device-master-port=2 --exec-server-task=3 -T typed device:hd0s2 task loaded: /lib/ld.so.1 /hurd/exec start /hurd/ext2fs.static: