[Top][All Lists]
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
parted and 78 heads
|
From: |
Mario Gzuk |
|
Subject: |
parted and 78 heads |
|
Date: |
Fri, 29 Sep 2006 14:56:42 +0200 |
Hi,
we have the following problem:
parted say that the disk (see below) has BIOS cylinder,head,sector
geometry: 9729,255,63.
But it writes other informations into the first sector of the fat
partition...
In sektor 1 of the fat32 partition the 2 bytes with offset 26 should
show the number of heads for interupt 0x13. And IMHO that should be the
same as parted gets from the BIOS.... Or am i wrong? But at these 2
bytes there is a value of "78" instead of "255". And also the 2 bytes
with offset 24 (which should contain the sectors per track for interupt
0x13) shows 60 instead of 63.
These all leads to the result of a "ntldr not found" problem.....
Maybe you can help me out of this ????
Here follows the system informations, if you need more let me know.
_____________SYSTEM INFORMATIONS_______________________________________
here is the output from "parted /dev/dsk print unit s print unit chs
print"
#parted start
Disk /dev/sda: 80.0GB
Sector size (logical/physical): 512B/512B
Partition Table: msdos
Number Start End Size Type File system Flags
1 0.51kB 4000MB 4000MB primary fat32 boot, lba
Disk /dev/sda: 156301487s
Sector size (logical/physical): 512B/512B
Partition Table: msdos
Number Start End Size Type File system Flags
1 1s 7812500s 7812500s primary fat32 boot, lba
Disk /dev/sda: 9729,80,62
Sector size (logical/physical): 512B/512B
BIOS cylinder,head,sector geometry: 9729,255,63. Each cylinder is
8225kB.
Partition Table: msdos
Number Start End Type File system Flags
1 0,0,1 486,77,59 primary fat32 boot, lba
### parted end
Here are some additional informations about the system
###dmesg start
BIOS-e820: 000000001ffd0000 - 0000000020000000 (ACPI NVS)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ff780000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
511MB LOWMEM available.
On node 0 totalpages: 131008
DMA zone: 4096 pages, LIFO batch:0
Normal zone: 126912 pages, LIFO batch:31
DMI 2.3 present.
ACPI: RSDP (v000 ACPIAM ) @
0x000f9ed0
ACPI: RSDT (v001 A M I OEMRSDT 0x02000616 MSFT 0x00000097) @
0x1ffc0000
ACPI: FADT (v002 A M I OEMFACP 0x02000616 MSFT 0x00000097) @
0x1ffc0200
ACPI: MADT (v001 A M I OEMAPIC 0x02000616 MSFT 0x00000097) @
0x1ffc0390
ACPI: OEMB (v001 A M I OEMBIOS 0x02000616 MSFT 0x00000097) @
0x1ffd0040
ACPI: DSDT (v001 A0128 A0128003 0x00000003 INTL 0x02002026) @
0x00000000
ACPI: PM-Timer IO Port: 0x4008
Allocating PCI resources starting at 30000000 (gap:
20000000:dec00000)
Built 1 zonelists
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 8192 bytes)
Detected 1808.896 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 491936k/524032k available (3565k kernel code, 31592k
reserved, 1735k data, 324k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor
mode... Ok.
Calibrating delay using timer specific routine.. 3620.14
BogoMIPS (lpj=1810070)
Security Framework v1.0.0 initialized
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 078bfbff e3d3fbff 00000000
00000000 00000001 00000000 00000001
CPU: After vendor identify, caps: 078bfbff e3d3fbff 00000000
00000000 00000001 00000000 00000001
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64
bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After all inits, caps: 078bfbff e3d3fbff 00000000 00000410
00000001 00000000 00000001
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: AMD Sempron(tm) Processor 3100+ stepping 02
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 0k freed
ACPI: setting ELCR to 0200 (from 0e88)
checking if image is initramfs... it is
Freeing initrd memory: 20974k freed
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=2
Setting up standard PCI resources
ACPI: Subsystem revision 20060127
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
Boot video device is 0000:01:00.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
ACPI: Power Resource [ISAV] (on)
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 9 10 11 12 14 15)
*0, disabled.
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 9 10 11 12 14 15)
*0, disabled.
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 9 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 9 10 11 12 14 15)
*0, disabled.
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LUS0] (IRQs *3 4 5 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LUS1] (IRQs 3 4 5 7 *9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LUS2] (IRQs 3 4 5 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LKLN] (IRQs 3 4 5 7 9 10 11 12 14 15)
*0, disabled.
ACPI: PCI Interrupt Link [LAUI] (IRQs 3 4 5 *7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LKMO] (IRQs 3 4 5 7 9 10 11 12 14 15)
*0, disabled.
ACPI: PCI Interrupt Link [LKSM] (IRQs 3 4 5 7 9 10 11 12 14 15)
*0, disabled.
ACPI: PCI Interrupt Link [LTID] (IRQs 10) *0
ACPI: PCI Interrupt Link [LTIE] (IRQs 10) *0, disabled.
ACPI: PCI Interrupt Link [LATA] (IRQs 3 4 6 7 10 11 12 *14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 15 devices
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps,
post a report
pnp: 00:0b: ioport range 0x480-0x487 has been reserved
pnp: 00:0b: ioport range 0xd00-0xd07 has been reserved
PCI: Bridge: 0000:00:0b.0
IO window: disabled.
MEM window: fd900000-fe9fffff
PREFETCH window: e9800000-ed7fffff
PCI: Bridge: 0000:00:0e.0
IO window: c000-cfff
MEM window: fea00000-feafffff
PREFETCH window: disabled.
PCI: Setting latency timer of device 0000:00:0e.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 4, 65536
bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 16384 bind 8192)
TCP reno registered
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
Total HugeTLB memory allocated, 0
NTFS driver 2.1.27 [Flags: R/O].
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Real Time Clock Driver v1.12ac
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected AGP bridge 0
agpgart: Setting up Nforce3 AGP.
agpgart: AGP aperture is 128M @ 0xf0000000
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
ibm_acpi: ec object not found
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing
disabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:0d: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64
irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
input: PC Speaker as /class/input/input0
input: AT Translated Set 2 keyboard as /class/input/input1
input: ImExPS/2 Generic Explorer Mouse as /class/input/input2
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024
blocksize
loop: loaded (max 8 devices)
nbd: registered device at major 43
Intel(R) PRO/1000 Network Driver - version 7.0.33-k2
Copyright (c) 1999-2005 Intel Corporation.
Intel(R) PRO/10GbE Network Driver - version 1.0.100-k2
Copyright (c) 1999-2005 Intel Corporation.
dgrs: SW=$Id: dgrs.c,v 1.13 2000/06/06 04:07:00 rick Exp $
FW=Build 550 11/16/96 03:45:15
FW Version=$Version$
pcnet32.c:v1.32 18.Mar.2006 address@hidden
e100: Intel(R) PRO/100 Network Driver, 3.5.10-k2-NAPI
e100: Copyright(c) 1999-2005 Intel Corporation
ThunderLAN driver v1.15
TLAN: 0 devices installed, PCI: 0 EISA: 0
ns83820.c: National Semiconductor DP83820 10/100/1000 driver.
forcedeth.c: Reverse Engineered nForce ethernet driver. Version
0.54.
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky <address@hidden>
ipw2100: Intel(R) PRO/Wireless 2100 Network Driver, git-1.2.2
ipw2100: Copyright(c) 2003-2006 Intel Corporation
ipw2200: Intel(R) PRO/Wireless 2200/2915 Network Driver,
git-1.1.1
ipw2200: Copyright(c) 2003-2006 Intel Corporation
STRIP: Version 1.3A-STUART.CHESHIRE (unlimited channels)
orinoco 0.15rc3 (David Gibson <address@hidden>,
Pavel Roskin <address@hidden>, et al)
orinoco_cs 0.15rc3 (David Gibson <address@hidden>,
Pavel Roskin <address@hidden>, et al)
orinoco_plx 0.15rc3 (Pavel Roskin <address@hidden>, David Gibson
<address@hidden>, Daniel Barlow <address@hidden>)
orinoco_pci 0.15rc3 (Pavel Roskin <address@hidden>, David Gibson
<address@hidden> & Jean Tourrilhes
<address@hidden>)
orinoco_tmd 0.15rc3 (Joerg Dorchain <address@hidden>)
orinoco_nortel 0.15rc3 (Tobias Hoffmann & Christoph Jungegger
<address@hidden>)
spectrum_cs 0.15rc3 (Pavel Roskin <address@hidden>, David Gibson
<address@hidden>, et al)
airo(): Probing for PCI adapters
airo(): Finished probing for PCI adapters
Loaded prism54 driver, version 1.2
hostap_cs: 0.4.4-kernel (Jouni Malinen <address@hidden>)
hostap_plx: 0.4.4-kernel (Jouni Malinen <address@hidden>)
hostap_pci: 0.4.4-kernel (Jouni Malinen <address@hidden>)
dmfe: Davicom DM9xxx net driver, version 1.36.4 (2002-01-17)
winbond-840.c:v1.01-d (2.4 port) Nov-17-2001 Donald Becker
<address@hidden>
http://www.scyld.com/network/drivers.html
Linux Tulip driver version 1.1.13 (May 11, 2002)
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:02:08.0[A] -> Link [LNKC] -> GSI 11
(level, low) -> IRQ 11
tulip0: EEPROM default media type Autosense.
tulip0: Index #0 - Media MII (#11) described by a 21142 MII PHY
(3) block.
tulip0: MII transceiver #17 config 1000 status 782d advertising
01e1.
eth0: Digital DS21143 Tulip rev 65 at 0001cc00,
00:00:CB:53:4C:5C, IRQ 11.
uli526x: ULi M5261/M5263 net driver, version 0.9.3 (2005-7-29)
libata version 1.20 loaded.
ieee1394: Initialized config rom entry `ip1394'
ieee1394: raw1394: /dev/raw1394 device initialized
usbmon: debugfs is not available
usbcore: registered new driver libusual
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
usbcore: registered new driver usblcd
usbcore: registered new driver usbled
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 10
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
ieee80211: 802.11 data/management/control stack, git-1.1.7
ieee80211: Copyright (C) 2004-2005 Intel Corporation
<address@hidden>
ieee80211_crypt: registered algorithm 'NULL'
ieee80211_crypt: registered algorithm 'WEP'
ieee80211_crypt: registered algorithm 'CCMP'
ieee80211_crypt: registered algorithm 'TKIP'
Using IPI Shortcut mode
ACPI wakeup devices:
PS2K PS2M UAR1 USB0 MAC USB1 USB2 P0P1
ACPI: (supports S0 S1 S3 S4 S5)
drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
Freeing unused kernel memory: 324k freed
3ware 9000 Storage Controller device driver for Linux
v2.26.02.007.
3ware Storage Controller device driver for Linux v1.26.02.001.
Loading Adaptec I2O RAID: Version 2.4 Build 5go
Detecting Adaptec I2O RAID controllers...
scsi: <fdomain> Detection failed (no card)
GDT-HA: Storage RAID Controller Driver. Version: 3.04
GDT-HA: Found 0 PCI Storage RAID Controllers
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override
with idebus=xx
ipr: IBM Power RAID SCSI Device Driver version: 2.1.3 (March 29,
2006)
iscsi: registered transport (tcp)
nsp32: loading...
sata_nv 0000:00:0a.0: version 0.8
ACPI: PCI Interrupt Link [LTID] BIOS reported IRQ 0, using IRQ
10
ACPI: PCI Interrupt Link [LTID] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LTID] -> GSI 10
(level, low) -> IRQ 10
PCI: Setting latency timer of device 0000:00:0a.0 to 64
ata1: SATA max UDMA/133 cmd 0x9F0 ctl 0xBF2 bmdma 0xD000 irq 10
ata2: SATA max UDMA/133 cmd 0x970 ctl 0xB72 bmdma 0xD008 irq 10
ata1: SATA link up 1.5 Gbps (SStatus 113)
ata1: dev 0 cfg 49:2f00 82:346b 83:7d01 84:4023 85:3469 86:3c01
87:4023 88:407f
ata1: dev 0 ATA-7, max UDMA/133, 156301488 sectors: LBA48
nv_sata: Primary device added
nv_sata: Primary device removed
nv_sata: Secondary device removed
ata1: dev 0 configured for UDMA/133
scsi0 : sata_nv
ata2: SATA link down (SStatus 0)
scsi1 : sata_nv
Vendor: ATA Model: ST3808110AS Rev: 3.AA
Type: Direct-Access ANSI SCSI revision:
05
SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: drive cache: write back
sda: sda1
sd 0:0:0:0: Attached scsi disk sda
sd 0:0:0:0: Attached scsi generic sg0 type 0
Adaptec aacraid driver (1.1-5[2409]-mh1)
Emulex LightPulse Fibre Channel SCSI driver 8.1.6
Copyright(c) 2004-2006 Emulex. All rights reserved.
megaraid cmm: 2.20.2.6 (Release Date: Mon Mar 7 00:01:03 EST
2005)
megaraid: 2.20.4.8 (Release Date: Mon Apr 11 12:27:22 EST 2006)
megasas: 00.00.02.04 Fri Feb 03 14:31:44 PST 2006
nsp_cs: loading...
QLogic Fibre Channel HBA Driver
Probing IDE interface ide0...
hda: TOSHIBA DVD-ROM SD-M1912, ATAPI CD/DVD-ROM drive
Probing IDE interface ide1...
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide-scsi is deprecated for cd burning! Use ide-cd and give
dev=/dev/hdX as device
scsi2 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: TOSHIBA Model: DVD-ROM SD-M1912 Rev: TM01
Type: CD-ROM ANSI SCSI revision:
00
sr0: scsi-1 drive
Uniform CD-ROM driver Revision: 3.20
sr 2:0:0:0: Attached scsi CD-ROM sr0
sr 2:0:0:0: Attached scsi generic sg1 type 5
NFORCE3-250: IDE controller at PCI slot 0000:00:08.0
NFORCE3-250: chipset revision 162
NFORCE3-250: not 100% native mode: will probe irqs later
NFORCE3-250: 0000:00:08.0 (rev a2) UDMA133 controller
NFORCE3-250: port 0x01f0 already claimed by ide0
ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:pio,
hdd:pio
Probing IDE interface ide1...
ACPI: PCI Interrupt Link [LUS2] enabled at IRQ 10
ACPI: PCI Interrupt 0000:00:02.2[C] -> Link [LUS2] -> GSI 10
(level, low) -> IRQ 10
PCI: Setting latency timer of device 0000:00:02.2 to 64
ehci_hcd 0000:00:02.2: EHCI Host Controller
ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus
number 1
ehci_hcd 0000:00:02.2: debug port 1
PCI: cache line size of 64 is not supported by device
0000:00:02.2
ehci_hcd 0000:00:02.2: irq 10, io mem 0xfebffc00
ehci_hcd 0000:00:02.2: USB 2.0 started, EHCI 1.00, driver 10 Dec
2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI)
Driver (PCI)
ACPI: PCI Interrupt Link [LUS0] enabled at IRQ 3
PCI: setting IRQ 3 as level-triggered
ACPI: PCI Interrupt 0000:00:02.0[A] -> Link [LUS0] -> GSI 3
(level, low) -> IRQ 3
PCI: Setting latency timer of device 0000:00:02.0 to 64
ohci_hcd 0000:00:02.0: OHCI Host Controller
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus
number 2
ohci_hcd 0000:00:02.0: irq 3, io mem 0xfebfd000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 4 ports detected
ACPI: PCI Interrupt Link [LUS1] enabled at IRQ 9
PCI: setting IRQ 9 as level-triggered
ACPI: PCI Interrupt 0000:00:02.1[B] -> Link [LUS1] -> GSI 9
(level, low) -> IRQ 9
PCI: Setting latency timer of device 0000:00:02.1 to 64
ohci_hcd 0000:00:02.1: OHCI Host Controller
ohci_hcd 0000:00:02.1: new USB bus registered, assigned bus
number 3
ohci_hcd 0000:00:02.1: irq 9, io mem 0xfebfe000
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 4 ports detected
USB Universal Host Controller Interface driver v3.0
BIOS EDD facility v0.16 2004-Jun-25, 1 devices found
eth0: Setting full-duplex based on MII#17 link partner
capability of 45e1.
eth0: no IPv6 routers present
###dmesg end
###lspci start
00:00.0 0600: 10de:00e1 (rev a1)
00:01.0 0601: 10de:00e0 (rev a2)
00:01.1 0c05: 10de:00e4 (rev a1)
00:02.0 0c03: 10de:00e7 (rev a1)
00:02.1 0c03: 10de:00e7 (rev a1)
00:02.2 0c03: 10de:00e8 (rev a2)
00:06.0 0401: 10de:00ea (rev a1)
00:08.0 0101: 10de:00e5 (rev a2)
00:0a.0 0101: 10de:00e3 (rev a2)
00:0b.0 0604: 10de:00e2 (rev a2)
00:0e.0 0604: 10de:00ed (rev a2)
00:18.0 0600: 1022:1100
00:18.1 0600: 1022:1101
00:18.2 0600: 1022:1102
00:18.3 0600: 1022:1103
01:00.0 0300: 102b:0525 (rev 85)
02:08.0 0200: 1011:0019 (rev 41)
00:00.0 Host bridge: nVidia Corporation nForce3 250Gb Host
Bridge (rev a1)
Subsystem: ASUSTeK Computer Inc. Unknown device 813f
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV-
VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Region 0: Memory at f0000000 (32-bit, prefetchable)
[size=128M]
Capabilities: [44] HyperTransport: Slave or Primary
Interface
Command: BaseUnitID=0 UnitCnt=14 MastHost-
DefDir- DUL-
Link Control 0: CFlE+ CST- CFE- <LkFail- Init+
EOC- TXO- <CRCErr=0 IsocEn- LSEn- ExtCTL- 64b-
Link Config 0: MLWI=16bit DwFcIn- MLWO=16bit
DwFcOut- LWI=16bit DwFcInEn- LWO=16bit DwFcOutEn-
Link Control 1: CFlE- CST- CFE- <LkFail+ Init-
EOC+ TXO+ <CRCErr=0 IsocEn- LSEn- ExtCTL- 64b-
Link Config 1: MLWI=8bit DwFcIn- MLWO=8bit
DwFcOut- LWI=8bit DwFcInEn- LWO=8bit DwFcOutEn-
Revision ID: 1.03
Link Frequency 0: 800MHz
Link Error 0: <Prot- <Ovfl- <EOC- CTLTm-
Link Frequency Capability 0: 200MHz+ 300MHz+
400MHz+ 500MHz+ 600MHz+ 800MHz+ 1.0GHz- 1.2GHz- 1.4GHz- 1.6GHz-
Vend-
Feature Capability: IsocFC+ LDTSTOP+ CRCTM-
ECTLT- 64bA- UIDRD-
Link Frequency 1: 200MHz
Link Error 1: <Prot- <Ovfl- <EOC- CTLTm-
Link Frequency Capability 1: 200MHz- 300MHz-
400MHz- 500MHz- 600MHz- 800MHz- 1.0GHz- 1.2GHz- 1.4GHz- 1.6GHz-
Vend-
Error Handling: PFlE- OFlE- PFE- OFE- EOCFE-
RFE- CRCFE- SERRFE- CF- RE- PNFE- ONFE- EOCNFE- RNFE- CRCNFE-
SERRNFE-
Prefetchable memory behind bridge Upper: 00-00
Bus Number: 00
Capabilities: [c0] AGP version 2.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh-
GART64- HTrans- 64bit- FW+ AGP3- Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64-
64bit- FW- Rate=x1
00:01.0 ISA bridge: nVidia Corporation nForce3 250Gb LPC Bridge
(rev a2)
Subsystem: ASUSTeK Computer Inc. Unknown device 813f
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV-
VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:01.1 SMBus: nVidia Corporation nForce 250Gb PCI System
Management (rev a1)
Subsystem: ASUSTeK Computer Inc. Unknown device 813f
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV-
VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 0
Region 0: I/O ports at 5080 [size=32]
Region 4: I/O ports at 5000 [size=64]
Region 5: I/O ports at 5040 [size=64]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:02.0 USB Controller: nVidia Corporation CK8S USB Controller
(rev a1) (prog-if 10 [OHCI])
Subsystem: ASUSTeK Computer Inc. Unknown device 813f
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV-
VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 3
Region 0: Memory at febfd000 (32-bit, non-prefetchable)
[size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:02.1 USB Controller: nVidia Corporation CK8S USB Controller
(rev a1) (prog-if 10 [OHCI])
Subsystem: ASUSTeK Computer Inc. Unknown device 813f
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV-
VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin B routed to IRQ 9
Region 0: Memory at febfe000 (32-bit, non-prefetchable)
[size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:02.2 USB Controller: nVidia Corporation nForce3 EHCI USB 2.0
Controller (rev a2) (prog-if 20 [EHCI])
Subsystem: ASUSTeK Computer Inc. Unknown device 813f
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV-
VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin C routed to IRQ 10
Region 0: Memory at febffc00 (32-bit, non-prefetchable)
[size=256]
Capabilities: [44] Debug port
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:06.0 Multimedia audio controller: nVidia Corporation nForce3
250Gb AC'97 Audio Controller (rev a1)
Subsystem: ASUSTeK Computer Inc. Unknown device 812a
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV-
VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (500ns min, 1250ns max)
Interrupt: pin A routed to IRQ 7
Region 0: I/O ports at e800 [size=256]
Region 1: I/O ports at ec00 [size=128]
Region 2: Memory at febfb000 (32-bit, non-prefetchable)
[size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:08.0 IDE interface: nVidia Corporation CK8S Parallel ATA
Controller (v2.5) (rev a2) (prog-if 8a [Master SecP PriP])
Subsystem: ASUSTeK Computer Inc. Unknown device 813f
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV-
VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Region 4: I/O ports at ffa0 [size=16]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0a.0 IDE interface: nVidia Corporation CK8S Serial ATA
Controller (v2.5) (rev a2) (prog-if 85 [Master SecO PriO])
Subsystem: ASUSTeK Computer Inc. Unknown device 813f
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV-
VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at 09f0 [size=8]
Region 1: I/O ports at 0bf0 [size=4]
Region 2: I/O ports at 0970 [size=8]
Region 3: I/O ports at 0b70 [size=4]
Region 4: I/O ports at d000 [size=16]
Region 5: I/O ports at dc00 [size=128]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:0b.0 PCI bridge: nVidia Corporation nForce3 250Gb AGP Host to
PCI Bridge (rev a2) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV-
VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 16
Bus: primary=00, secondary=01, subordinate=01,
sec-latency=10
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: fd900000-fe9fffff
Prefetchable memory behind bridge: e9800000-ed7fffff
Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity+ SERR+ NoISA- VGA+ MAbort- >Reset-
FastB2B-
00:0e.0 PCI bridge: nVidia Corporation nForce3 250Gb PCI-to-PCI
Bridge (rev a2) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV-
VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast
>TAbort- <TAbort- <MAbort- >SERR+ <PERR-
Latency: 0
Bus: primary=00, secondary=02, subordinate=02,
sec-latency=128
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: fea00000-feafffff
Prefetchable memory behind bridge: fff00000-000fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort+ <SERR- <PERR+
BridgeCtl: Parity+ SERR+ NoISA- VGA- MAbort- >Reset-
FastB2B-
00:18.0 Host bridge: Advanced Micro Devices [AMD] K8
[Athlon64/Opteron] HyperTransport Technology Configuration
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV-
VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Capabilities: [80] HyperTransport: Host or Secondary
Interface
!!! Possibly incomplete decoding
Command: WarmRst+ DblEnd-
Link Control: CFlE- CST- CFE- <LkFail- Init+
EOC- TXO- <CRCErr=0
Link Config: MLWI=16bit MLWO=16bit LWI=16bit
LWO=16bit
Revision ID: 1.02
00:18.1 Host bridge: Advanced Micro Devices [AMD] K8
[Athlon64/Opteron] Address Map
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV-
VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
00:18.2 Host bridge: Advanced Micro Devices [AMD] K8
[Athlon64/Opteron] DRAM Controller
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV-
VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
00:18.3 Host bridge: Advanced Micro Devices [AMD] K8
[Athlon64/Opteron] Miscellaneous Control
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV-
VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
01:00.0 VGA compatible controller: Matrox Graphics, Inc. MGA
G400/G450 (rev 85) (prog-if 00 [VGA])
Subsystem: Matrox Graphics, Inc. Millennium G450 32Mb
SDRAM Dual Head
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV-
VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (4000ns min, 8000ns max), Cache Line Size 08
Interrupt: pin A routed to IRQ 11
Region 0: Memory at ea000000 (32-bit, prefetchable)
[size=32M]
Region 1: Memory at fe9fc000 (32-bit, non-prefetchable)
[size=16K]
Region 2: Memory at fe000000 (32-bit, non-prefetchable)
[size=8M]
Expansion ROM at fe9c0000 [disabled] [size=128K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [f0] AGP version 2.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh-
GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2,x4
Command: RQ=32 ArqSz=0 Cal=0 SBA+ AGP+ GART64-
64bit- FW- Rate=x1
02:08.0 Ethernet controller: Digital Equipment Corporation
DECchip 21142/43 (rev 41)
Subsystem: Compu-Shack Unknown device 4235
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+
VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (5000ns min, 10000ns max), Cache Line Size
08
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at cc00 [size=128]
Region 1: Memory at feaffc00 (32-bit, non-prefetchable)
[size=1K]
Expansion ROM at fea80000 [disabled] [size=256K]
###lspci end
###fdisk start
Disk /dev/sda: 80.0 GB, 80026361856 bytes
255 heads, 63 sectors/track, 9729 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
###fdsik end
###memeinfo start
MemTotal: 513352 kB
MemFree: 434436 kB
Buffers: 0 kB
Cached: 64844 kB
SwapCached: 0 kB
Active: 18068 kB
Inactive: 49084 kB
HighTotal: 0 kB
HighFree: 0 kB
LowTotal: 513352 kB
LowFree: 434436 kB
SwapTotal: 0 kB
SwapFree: 0 kB
Dirty: 0 kB
Writeback: 0 kB
Mapped: 3988 kB
Slab: 8128 kB
CommitLimit: 256676 kB
Committed_AS: 4452 kB
PageTables: 120 kB
VmallocTotal: 507896 kB
VmallocUsed: 3068 kB
VmallocChunk: 504636 kB
HugePages_Total: 0
HugePages_Free: 0
HugePages_Rsvd: 0
Hugepagesize: 4096 kB
###meminfo end
###cpuinfo start
processor : 0
vendor_id : AuthenticAMD
cpu family : 15
model : 44
model name : AMD Sempron(tm) Processor 3100+
stepping : 2
cpu MHz : 1808.896
cache size : 256 KB
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 1
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep
mtrr pge mca cmov pat pse36 clflush mmx fxsr sse sse2 syscall nx
mmxext fxsr_opt lm 3dnowext 3dnow up pni lahf_lm ts fid vid ttp
tm stc
bogomips : 3620.14
###cpuinfo end
greetings mario gzuk
| [Prev in Thread] |
Current Thread |
[Next in Thread] |
- parted and 78 heads,
Mario Gzuk <=