[Top][All Lists]
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
Re: [Discuss-gnuradio] wxPython and FC3
From: |
Sachi |
Subject: |
Re: [Discuss-gnuradio] wxPython and FC3 |
Date: |
Thu, 24 Mar 2005 22:48:05 -0800 (PST) |
I also use FC3, for wxPython, my way is:
from the download page:
https://sourceforge.net/project/showfiles.php?group_id=10718
download the following rpms
wxPython2.5-gtk2-unicode-2.5.4.1-fc2_py2.3.i386.rpm
wxPython-common-gtk2-unicode-2.5.4.1-fc2_py2.3.i386.rpm
wxPython2.5-devel-gtk2-unicode-2.5.4.1-fc2_py2.3.i386.rpm
if you r using python 2.4, you should change them
correspondingly. That works
Dawei
--- address@hidden wrote:
> What is the best way to get wxPython working under
> Fedora Core 3?
>
> I tried to download and build the source, but it has
> been very painful.
>
> When I run the program I typically get core dumps:
>
> address@hidden usrp]$ ./usrp_fft.py
> usrp: found usrp rev2
> RX d'board A: Basic Rx
> RX d'board B: Basic Rx
> Segmentation fault (core dumped)
> address@hidden usrp]$
>
> address@hidden usrp]$ ./wfm_rcv_gui.py 10.7
> usrp: found usrp rev2
> RX d'board A: Basic Rx
> RX d'board B: Basic Rx
> usrp_standard_rx::set_decim_rate: WARNING rates >
> 128 result in incorrect
> gain.
> >>> gr_fir_fff: using SSE
> Segmentation fault (core dumped)
>
>
> On a good note, the O'scope works alright
> usrp_oscope.py
>
> Thanks for any assitance...
>
>
> The following was my last build attempt:
>
> tar zxf wxPython-src-2.5.4.1.tar.gz
> cd wxPython-src-2.5.4.1
> mkdir bld
> cd bld
> ../configure --prefix=$HOME/gr \
> --enable-rpath=$HOME/gr \
> --with-gtk \
> --with-opengl \
> --enable-debug \
> --enable-geometry \
> --enable-sound --with-sdl \
> --enable-display \
> --disable-debugreport \
> --with-libjpeg=builtin \
> --with-libpng=builtin \
> --with-libtiff=builtin \
> --with-zlib=builtin
>
> make
> make -C contrib/src/gizmos
> make -C contrib/src/stc
>
> make install
> make install -C contrib/src/gizmos
> make install -C contrib/src/stc
>
> cd ../wxPython
> python setup.py build
> python setup.py install --prefix=$HOME/gr
> cd
>
>
>
> I'm using the following support packages:
>
> tar zxf fftw-3.0.1.tar.gz
> tar xzf swig-1.3.24.tar.gz
> tar xzf cppunit-1.10.2.tar.gz
> tar xzf sdcc-2.4.0.tar.gz
> tar zxf xerces-c-src_2_6_0.tar.gz
>
>
> The of the GNU radio core compiles and runs without
> any problems.
>
>
>
> _______________________________________________
> Discuss-gnuradio mailing list
> address@hidden
>
http://lists.gnu.org/mailman/listinfo/discuss-gnuradio
>
__________________________________
Do you Yahoo!?
Yahoo! Small Business - Try our new resources site!
http://smallbusiness.yahoo.com/resources/