Re: [Discuss-gnuradio] problem with USRP

[Tushar Patel]

Hi try to run usrp_oscope.py and usrp_fft.py, which are gui type exaples.
but application run then it show oUoUoU error,
which I fount the USRP overrun.
I run all this on VMware platform.
I am using amd 64 turion, 3gb ram configuration.
So I do not able to understand why my system getting low.

Also I would like to run FM radio, I have only one tx and one rx board, can I run sterio FM, 

thanks and regards
tushar

On Thu, Jan 29, 2009 at 1:58 PM, Mir Ali <address@hidden> wrote:

great. test your installation with the following programs to start with. Look in the following directory /usr/local/share/gnuradio/examples

There are lots of examples that you can start with. In the digital directory you can use benchmark_tx.py and bechmark_rx.py to test transmit and receive using two USRPs. You can use tunnel.py to make usrp behave as ethernet . Test the sound card using the programs in audio directory.

If you have questions then ask us. :-)

Bye
Ali

On Thu, Jan 29, 2009 at 2:10 AM, Tushar Patel <address@hidden> wrote:

Hi I able to detect the USPR board with VM ware player.
I also test with the command shows in help
ls -lR /dev/bus/usb | grep usrp
 i got the output as per mention,
Now I have the basic Tx and basic Rx board, so what are the example availble on which I can run with these basic Tx anr basic Rx board ?
thanks and regards
tushar patel

On Wed, Jan 28, 2009 at 1:21 PM, Mir Ali <address@hidden> wrote:

Did u do as Eric asked you to? Download the latest gnuradio svn tar and follow the install instructions.

On Wed, Jan 28, 2009 at 2:52 PM, Tushar Patel <address@hidden> wrote:

I found the linux/compiler.h file in other place, I gave the path in fusb_linux.cc and able to run all make, check make, install make.

It will gererate the usrp_firmware.ihx file also but it will generate in rev0 and rev1, I used the usrp-0.5 tar from your link.

 still I do not able to detact my USRP hardware,

so that USRP tar is old or what, I do not able to resolve it

pl. guide me

On Sun, Jan 25, 2009 at 9:07 PM, Eric Blossom <address@hidden> wrote:

On Sun, Jan 25, 2009 at 05:14:55PM -0800, Tushar Patel wrote:
> ---------- Forwarded message ----------
> From: Tushar Patel <address@hidden>
> Date: Fri, 23 Jan 2009 21:28:32 -0800
> Subject: problem with USRP
> To: Eric Blossom <address@hidden>
>
> Hi Eric,
> I used the VM Ware player , on which i run my linux- UBUNTU-8.04
> I am able to configure all gnu software packages perfectly, I was able to
> run "hello world" example.

You appear to be compiling ancient code.

Please use either the svn trunk or the latest tarball.

 http://gnuradio.org/trac/wiki/Download
 http://gnuradio.org/trac/wiki/BuildGuide

Eric

_______________________________________________
Discuss-gnuradio mailing list
address@hidden
http://lists.gnu.org/mailman/listinfo/discuss-gnuradio

--
Mir Murtuza Ali
Graduate Student
Center for Wireless Communications
University of Mississippi
University, MS 38677

_______________________________________________
Discuss-gnuradio mailing list
address@hidden
http://lists.gnu.org/mailman/listinfo/discuss-gnuradio