[Top][All Lists]
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
Re: [Discuss-gnuradio] Full duplex and half duplex doesnot work
From: |
Lebowski80 |
Subject: |
Re: [Discuss-gnuradio] Full duplex and half duplex doesnot work |
Date: |
Tue, 30 Nov 2010 03:10:40 -0800 (PST) |
How did you resolve your problem? I have the same problem and reading your
post I cannot understand the solution of your one.
Thanks in advance
blwfsoj wrote:
>
> Hi all,
> Before i start telling about my problem, i want to mention that i have
> already read the post named "help: cannot send after transport endpoint
> shutdown" which is very close to my problem but i could not solve it.
>
> I'm trying to transmit from the usrp port A, and then make it receive at
> the same port using "Auto T/R" which i expressed by typing "-v" (isn't it
> correct) after the benchmark.
> but some time it works and most of the times its not (not stable), when
> its not working it shows me the following error:
> address@hidden:~/Documents/abbasi/programmitx.py -f 1200000000 -m dbpsk -v
> --tx-amplitude=0.08 -T A
>>>> gr_fir_ccf: using SSE
>
> Modulator:
> bits per symbol: 1
> Gray code: True
> RRC roll-off factor: 0.35
> Tx amplitude 0.08
> modulation: dbpsk_mod
> bitrate: 100kb/s
> samples/symbol: 2
> USRP Sink: A: Flex 1200 Tx MIMO B
> Requested TX Bitrate: 100k Actual Bitrate: 125k
> Warning: failed to enable realtime scheduling
> address@hidden:~/Documents/abbasi/programmirx.py
> -f 1200000000 -m dbpsk -v
>>>> gr_fir_ccf: using SSE
>
> Demodulator:
> bits per symbol: 1
> Gray code: True
> RRC roll-off factor: 0.35
> Costas Loop alpha: 1.50e-01
> Costas Loop beta: 5.62e-03
> M&M mu: 0.50
> M&M mu gain: 1.00e-01
> M&M omega: 2.00
> M&M omega gain: 2.50e-03
> M&M omega limit: 0.01
>
> Receive Path:
> modulation: dbpsk_demod
> bitrate: 100kb/s
> samples/symbol: 2
> usrp_open_interface:usb_claim_interface: failed interface 2
> could not claim interface 2: Device or resource busy
> usrp_basic_rx: can't open rx interface
> Traceback (most recent call last):
> File "mybenchmark_rx.py", line 112, in <module>
> main()
> File "mybenchmark_rx.py", line 101, in main
> tb = my_top_block(demods[options.modulation], rx_callback, options)
> File "mybenchmark_rx.py", line 45, in __init__
> self.rxpath = usrp_receive_path.usrp_receive_path(demodulator,
> rx_callback, options)
> File
> "/home/onur/Documents/abbasi/programming/examples/digital/usrp_receive_path.py",
> line 68, in __init__
> self._setup_usrp_source(options)
> File
> "/home/onur/Documents/abbasi/programming/examples/digital/usrp_receive_path.py",
> line 73, in _setup_usrp_source
> self.u = usrp_options.create_usrp_source(options)
> File
> "/home/onur/Documents/abbasi/programming/examples/digital/usrp_options.py",
> line 88, in create_usrp_source
> gain=options.rx_gain,
> File
> "/home/onur/Documents/abbasi/programming/examples/digital/generic_usrp.py",
> line 144, in __init__
> _generic_usrp_base.__init__(self, **kwargs)
> File
> "/home/onur/Documents/abbasi/programming/examples/digital/generic_usrp.py",
> line 63, in __init__
> except: raise Exception, 'Failed to automatically setup a usrp
> device.'
> Exception: Failed to automatically setup a usrp device.
> address@hidden:~/Documents/abbasi/programming/examples/digital$
>
> ON THE OTHER HAND:
> when i try the full duplex (use a slot from block A as transmitter and
> slot from block B as receiver) it also doesnot work. it will not be able
> to setup the interface.
>
> i appreciate your help,
> regards,
>
>
--
View this message in context:
http://old.nabble.com/Full-duplex-and-half-duplex-doesnot-work-tp27226209p30338716.html
Sent from the GnuRadio mailing list archive at Nabble.com.
[Prev in Thread] |
Current Thread |
[Next in Thread] |
- Re: [Discuss-gnuradio] Full duplex and half duplex doesnot work,
Lebowski80 <=