[Top][All Lists]
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
[Discuss-gnuradio] UHD + USRP2, not working with RFX400
From: |
Gaetano Mendola |
Subject: |
[Discuss-gnuradio] UHD + USRP2, not working with RFX400 |
Date: |
Thu, 3 Feb 2011 10:10:41 +0100 |
Hi,
I was able to install the UHD on my host and as well the firmware on the SSD,
I changed the USRP2 ip address to 192.168.0.2.
The uhd_find_devices correctly finds the device:
$ uhd_find_devices
linux; GNU C++ version 4.4.3; Boost_104000; UHD_002.20110131232513.d46058d
--------------------------------------------------
-- UHD Device 0
--------------------------------------------------
Device Address:
type: usrp2
addr: 192.168.0.2
name:
serial: 997
so far so well.
Launching the example ./tx_waveforms --freq 430000000 --duration 60000
however I do not get the expected result (I don't see the beacon on my
frequency
analyzer), using a WBX all seems working fine.
Using RFX400:
./tx_waveforms --freq 430000000 --duration 60000
linux; GNU C++ version 4.4.3; Boost_104000; UHD_002.20110131232513.d46058d
Creating the usrp device with: ...
Current recv sock buff size: 50000000 bytes
mboard0 MIMO master
Using Device: Single USRP:
Device: USRP2/N Series device
Mboard: USRP2-REV4 mboard
RX DSP: USRP2-REV4 ddc0
RX Channel: 0
RX Dboard: USRP2-REV4 dboard (rx unit)
RX Subdev: RFX400 (0x0024)
TX DSP: USRP2-REV4 duc0
TX Channel: 0
TX Dboard: USRP2-REV4 dboard (tx unit)
TX Subdev: RFX400 (0x0028)
Setting TX Rate: 1.500000 Msps...
Warning:
The hardware does not support the requested TX sample rate:
Target sample rate: 1.500000 MSps
Actual sample rate: 1.492537 MSps
Actual TX Rate: 1.492537 Msps...
Setting TX Freq: 430.000000 Mhz...
Actual TX Freq: 430.000000 Mhz...
Setting TX Gain: 0.000000 dB...
Actual TX Gain: 0.000000 dB...
and this using the WBX:
$ ./tx_waveforms --freq 430000000 --duration 60000
linux; GNU C++ version 4.4.3; Boost_104000; UHD_002.20110131232513.d46058d
Creating the usrp device with: ...
Current recv sock buff size: 50000000 bytes
mboard0 MIMO master
Using Device: Single USRP:
Device: USRP2/N Series device
Mboard: USRP2-REV4 mboard
RX DSP: USRP2-REV4 ddc0
RX Channel: 0
RX Dboard: USRP2-REV4 dboard (rx unit)
RX Subdev: WBX (0x0053)
TX DSP: USRP2-REV4 duc0
TX Channel: 0
TX Dboard: USRP2-REV4 dboard (tx unit)
TX Subdev: WBX (0x0052)
Setting TX Rate: 1.500000 Msps...
Warning:
The hardware does not support the requested TX sample rate:
Target sample rate: 1.500000 MSps
Actual sample rate: 1.492537 MSps
Actual TX Rate: 1.492537 Msps...
Setting TX Freq: 430.000000 Mhz...
Actual TX Freq: 430.000000 Mhz...
Setting TX Gain: 0.000000 dB...
Actual TX Gain: 0.000000 dB...
Has anyone got same issue using UHD + USRP2( RFX400) ?
Regards
Gaetano Mendola
--
cpp-today.blogspot.com
[Prev in Thread] |
Current Thread |
[Next in Thread] |
- [Discuss-gnuradio] UHD + USRP2, not working with RFX400,
Gaetano Mendola <=