I assume these are old systems?
Sent from my iPhone On Sep 8, 2021, at 1:19 PM, isaac mario tupac davila <isacctd92@gmail.com> wrote:
Hi
It seems the problem is the Rx daughterboard because I changed the USRP, used the same flowgraph in GRC and it has worked.
Thanks for the help. Regards Isaac T.
On 2021-09-06 5:33 p.m., isaac mario
tupac davila wrote:
Hi
I've probed A:A, A:B, A:AB, A:BA and had the same behavior.
Doesn't change.
regards
Isaac T
This should make NO DIFFERENCE, but what version of Gnu Radio are
you using?
The fact that you're using WX GUI bits and pieces probably means
something somewhat old.
The "modern" approach would be to use Qt GUI elements that do very
similar things to what
the (deprecated for quite some time) WX GUI bits and pieces do.
On 2021-09-06 3:24 p.m., isaac mario tupac davila
wrote:
Hi.
-- The daughterboard is the BasicRX Daughterboard.
-- I put the address of my USRP as 192.168.10.1
******************************************************************************************************
soporte@i28:~$ ping 192.168.10.1
PING 192.168.10.1 (192.168.10.1) 56(84) bytes of data.
64 bytes from 192.168.10.1:
icmp_seq=1 ttl=64 time=0.051 ms
64 bytes from 192.168.10.1:
icmp_seq=2 ttl=64 time=0.051 ms
64 bytes from 192.168.10.1:
icmp_seq=3 ttl=64 time=0.049 ms
******************************************************************************************************
soporte@28:~$ uhd_usrp_probe --args type=n200
Try setting a subdev spec of:
A:A
Error: LookupError: KeyError: No devices found for
----->
Device Address:
type: n200
*******************************************************************************************************
soporte@28:~$ uhd_find_devices
[INFO] [UHD] linux; GNU C++ version 7.5.0;
Boost_106501; UHD_3.14.1.1-0-g7c0291ad
--------------------------------------------------
-- UHD Device 0
--------------------------------------------------
Device Address:
serial: 3176CEA
addr: 192.168.10.2
name:
type: usrp2
*******************************************************************************************************
soporte@28:~$ uhd_usrp_probe
[INFO] [UHD] linux; GNU C++ version 7.5.0;
Boost_106501; UHD_3.14.1.1-0-g7c0291ad
[INFO] [USRP2] Opening a USRP2/N-Series device...
[INFO] [USRP2] Current recv frame size: 1472 bytes
[INFO] [USRP2] Current send frame size: 1472 bytes
[WARNING] [USRP2] Unable to identify device - assuming
USRP2/N-Series device
[WARNING] [UHD] Unable to set the thread priority.
Performance may be negatively affected.
Please see the general application notes in the manual
for instructions.
EnvironmentError: OSError: error in
pthread_setschedparam
_____________________________________________________
/
| Device: USRP2 / N-Series Device
|
_____________________________________________________
| /
| | Mboard: N???
| | mac-addr: 00:2c:00:00:00:24
| | ip-addr: 0.0.0.0
| | subnet: 0.0.0.0
| | gateway: 255.255.255.255
| | gpsdo: none
| | serial: 3176CEA
| | FW Version: 12.3
| | FPGA Version: 10.0
| |
| | Time sources: none, external, _external_,
mimo
| | Clock sources: internal, external, mimo
| | Sensors: mimo_locked, ref_locked
| |
_____________________________________________________
| | /
| | | RX DSP: 0
| | |
| | | Freq range: -50.000 to 50.000 MHz
| |
_____________________________________________________
| | /
| | | RX DSP: 1
| | |
| | | Freq range: -50.000 to 50.000 MHz
| |
_____________________________________________________
| | /
| | | RX Dboard: A
| | | ID: Basic RX (0x0001)
| | | Serial: 315A5DF
| | |
_____________________________________________________
| | | /
| | | | RX Frontend: AB
| | | | Name: BasicRX (AB)
| | | | Antennas:
| | | | Sensors:
| | | | Freq range: -250.000 to 250.000 MHz
| | | | Gain Elements: None
| | | | Bandwidth range: 500000000.0 to
500000000.0 step 0.0 Hz
| | | | Connection Type: IQ
| | | | Uses LO offset: No
| | |
_____________________________________________________
| | | /
| | | | RX Frontend: BA
| | | | Name: BasicRX (BA)
| | | | Antennas:
| | | | Sensors:
| | | | Freq range: -250.000 to 250.000 MHz
| | | | Gain Elements: None
| | | | Bandwidth range: 500000000.0 to
500000000.0 step 0.0 Hz
| | | | Connection Type: QI
| | | | Uses LO offset: No
| | |
_____________________________________________________
| | | /
| | | | RX Frontend: A
| | | | Name: BasicRX (A)
| | | | Antennas:
| | | | Sensors:
| | | | Freq range: -250.000 to 250.000 MHz
| | | | Gain Elements: None
| | | | Bandwidth range: 250000000.0 to
250000000.0 step 0.0 Hz
| | | | Connection Type: I
| | | | Uses LO offset: No
| | |
_____________________________________________________
| | | /
| | | | RX Frontend: B
| | | | Name: BasicRX (B)
| | | | Antennas:
| | | | Sensors:
| | | | Freq range: -250.000 to 250.000 MHz
| | | | Gain Elements: None
| | | | Bandwidth range: 250000000.0 to
250000000.0 step 0.0 Hz
| | | | Connection Type: Q
| | | | Uses LO offset: No
| | |
_____________________________________________________
| | | /
| | | | RX Codec: A
| | | | Name: ??????
| | | | Gain Elements: None
| |
_____________________________________________________
| | /
| | | TX DSP: 0
| | |
| | | Freq range: -200.000 to 200.000 MHz
| |
_____________________________________________________
| | /
| | | TX Dboard: A
| | |
_____________________________________________________
| | | /
| | | | TX Frontend: 0
| | | | Name: Unknown (0xffff) - 0
| | | | Antennas:
| | | | Sensors:
| | | | Freq range: 0.000 to 0.000 MHz
| | | | Gain Elements: None
| | | | Bandwidth range: 0.0 to 0.0 step 0.0
Hz
| | | | Connection Type: IQ
| | | | Uses LO offset: No
| | |
_____________________________________________________
| | | /
| | | | TX Codec: A
| | | | Name: ad9777
| | | | Gain Elements: None
[WARNING] [UHD] Unable to set the thread priority.
Performance may be negatively affected.
Please see the general application notes in the manual
for instructions.
EnvironmentError: OSError: error in
pthread_setschedparam
[WARNING] [UHD] Unable to set the thread priority.
Performance may be negatively affected.
Please see the general application notes in the manual
for instructions.
EnvironmentError: OSError: error in
pthread_setschedparam
****************************************************************************************************************
I'm not completely sure what is happening. it seems
I have an USRP2. I put it wit address 192.168.10.1,
but when I run uhd_find_devices is with 192.168.10.2
¿Could be that?
Isaac T.
Hi Isaac,
On 9/6/21 6:02 PM, isaac mario tupac davila wrote:
> I'm Isaac. I am trying to discover what is
happening with my USRP N200.
> I'm sending a signal of 100mVpp and 1MHz from a
signal generator to
> channel RF 2 of my USRP N200 but I receive a 0v
signal and a constant
> -230db (if I see it in a FFT block).
Please include which RX daughterboard you are using
with the N200? What
is RF2 connected to internally in the USRP? Does
channel RF1 work for you?
In your flowchart, you're using a center frequency of
1 MHz with a
sampling rate of 10 MS/s, which is a bit odd, although
it shouldn't
prevent you from seeing the signal.
Your scope plot and FFT plot look as if you're not
receiving anything,
not even noise.
You should probably first of all verify whether your
PC can even talk to
the USRP properly, e.g. by running 'uhd_find_devices'
and 'uhd_usrp_probe'.
Regards, Paul Boven.
|