Re: [Orgmode] remote reference

[Carsten Dominik]

On Dec 11, 2010, at 3:42 PM, Karl Eichwalder wrote:

> Carsten Dominik <address@hidden> writes:
>
> > Fixed, thanks.
>
> It is not fixed in the 23.2.91 pre-release, which comes with org  
> 6.33x.
> It did not check any other repository (which one?).

This is fixed in our own repository at http://repo.or.cz/w/org-mode.git

It will be in Emacs only with the Emacs 24 release.

- Carsten



> > On May 12, 2010, at 1:26 PM, Karl Eichwalder wrote:
> >
> > > Carsten Dominik <address@hidden> writes:
> > >
> > > > On May 11, 2010, at 9:16 PM, Karl Eichwalder wrote:
> > > > > C-c C-c in a TBLFM with a remote table reference updates the table
> > > > > as
> > > > > expected, but also jumps to the referenced table in the remote  
> > > > > file.
> > > > > Is
> > > > > this intended?  If yes, is it possible to avoid it?
> > > >
> > > > Can you please be more specific.  What exactly happens?
> > >
> > > Consider the following two files:
> > >
> > > * 2009
> > > #+TBLNAME: 2009
> > > :PROPERTIES:
> > > :ID:       ea32e5b5-31ba-468e-8e31-3e0d09696bb0
> > > :END:
> > > |-----+-------|
> > > |  mm |    km |
> > > |-----+-------|
> > > | all | 946.8 |
> > > |-----+-------|
> > >
> > > * 2010
> > > #+TBLNAME: 2010
> > > :PROPERTIES:
> > > :ID:       e0df84c4-8abc-458f-a1ee-eb53eb71b4f0
> > > :END:
> > > |-----+-------+-------+-------|
> > > |  mm |    km |  B km |  G km |
> > > |-----+-------+-------+-------|
> > > | all | 249.4 | 429.2 | 678.6 |
> > > |-----+-------+-------+-------|
> > >
> > > * all
> > > :PROPERTIES:
> > > :ID:       44751a7f-73a4-4c07-b3c2-e3edb9042acd
> > > :END:
> > > #+TBLNAME: all
> > > |------+--------|
> > > | yyyy |     km |
> > > |------+--------|
> > > | 2009 |        |
> > > | 2010 |  678.6 |
> > > |------+--------|
> > > |  all | 1625.4 |
> > > |------+--------|
> > > #+TBLFM: @2$2=remote(ea32e5b5-31ba-468e-8e31-3e0d09696bb0,$LR2);%.
> > > 1f::@3$2=remote(2010,$LR4);%.1f::$LR2=vsum(@address@hidden);%.1f
> > >
> > > Then, in the 2010 file, eval the formula of the "all" table by
> > > pressing
> > > C-c C-c.
> > > ==>
> > >
> > > It takes the km value from the 2009 file, but also puts the cursor
> > > (point) into the 2009 file in front of the ID:
> > >
> > > * 2009
> > > #+TBLNAME: 2009
> > > :PROPERTIES:
> > > :ID:       -!-ea32e5b5-31ba-468e-8e31-3e0d09696bb0
> > > :END:
> > > |-----+-------|
> > > |  mm |    km |
> > > |-----+-------|
> > > | all | 946.8 |
> > > |-----+-------|
> > >
> > > -=-=-=-=-=-=-=-=-=-=-=-=-=- cut here -=-=-=-=-=-=-=-=-=-=-=-=-=-
> > >
> > > I'd prefer if the point would stay in the 2010 file.
> > >
> > > --
> > > Karl Eichwalder
> >
> > - Carsten
>
> --
> Karl Eichwalder