Nokia 6610 doesn't work

[Ulrich Janke]

Hi experts,

I have a brandnew Nokia 6610 mobile phone and I would like to use it 
under SuSE Linux 8.2.
The device works with HSCSD andnd GPRS very well under Win2K but 
unfortunately not under Linux.
When I do an irdadump I receive the following output what seems to be ok:

12:31:57.014408 xid:cmd bca55b1a > ffffffff S=6 s=0 (14)
12:31:57.104412 xid:cmd bca55b1a > ffffffff S=6 s=1 (14)
12:31:57.194401 xid:cmd bca55b1a > ffffffff S=6 s=2 (14)
12:31:57.284399 xid:cmd bca55b1a > ffffffff S=6 s=3 (14)
12:31:57.361765 xid:rsp bca55b1a < 000069b5 S=6 s=3 Nokia 6610 hint=b125 
[ PnP Modem Fax Telephony IrCOMM IrOBEX ] (27)

When I try to dial-in over wvdial I recognize that my mobile perhaps 
doesn't understand any AT commands:

--> WvDial: Internet dialer version 1.42
--> Initializing modem.
--> Sending: ATZ
--> Sending: ATQ0
--> Re-Sending: ATZ
--> Modem not responding.

Then I tried to use gnokii for a connection:

gnokii -version
GNOKII Version 0.5.2
Use 'gnokii --help' for usage information.

I tried to identify my modem device as next:

gnokii --identify
GNOKII Version 0.5.2
Couldn't open PHONET device: Success
Telephone interface init failed: Command failed.
Quitting.

My .gnokiirc has been attached. Do you have any idea what may be wrong? 
Is it a generic configuration problem or may Nokia have changed the 
firmware?
BTW: I asked Nokia for a Linux support and got an answer that this OS is 
not supported ;-(

Thanks in advance!

Ulrich

# This is a sample ~/.gnokiirc file.  Copy it into your
# home directory and name it .gnokiirc.
#

[global]

# Set port to the physical serial port used to connect to your phone.
# Linux version is:
port = /dev/ircomm0
# For MacOSX you will need something like:
# port = /dev/cu.USA28X1P1.1
#
# Use this setting also for the Bluetooth connection:
# port = aa:bb:cc:dd:ee:ff
 
# Set model to the model number of your phone
model = 6610

# Initlength controls the number of characters sent to the
# phone during initialisation.  You can either set it to
# the word "default" or a positive integer.
# 
# You can try setting this value if you want to connect
# to the phone quicker.  If you've never noticed the
# connection to be slow, it is suggested that you 
# leave this alone.  Read the initialisation code in fbus-xxxx
# to understand what this changes if you're curious.
initlength = default

# The type of the connection, for IR set this to infrared or irda.
# For the nk6110 driver only infrared is valid for the IrDA connection.
# See Docs/gnokii-ir-howto for more detailes on this.
# If you have 6210/6250/7110 phone and dau9p cable (the one you can
# use with 6100 series and cannot use hardware modem from the phone)
# you may want to use 'dau9p' value to get faster initialization.
# If you use dlr3 or dlr3p cable for nokia phones in FBUS mode (ie.
# you don't use model = AT) you may want to use 'dlr3p' value here.
# Note that it is recommended and currently the best way to use this
# cable with nk6510 driver.
connection = irda

# Set bindir to point to the location of the various gnokii binaries.
# In particular ensure that mgnokiidev is in this location, with
# permissions 4750, owned by root, group gnokii.  Ensure you
# are in the gnokii group and that the group exists...
bindir = /usr/local/sbin/

# Set this to 'yes' if you want gnokii to set and check the lock file in
# /var/lock directory. It avoids potential conflicts with other serial
# port software (eg. minicom). If you have wrong permissions for the
# directory, a warning will be generated. If you don't want a lockfile, set
# it to 'no'.
use_locking = no

# Baudrate to use on serial port connections.
# Currently used only by models AT and BIP/CIMD. Defaults to 19200.
serial_baudrate = 115200

# Force waiting after each send character the specified usec time.
# Value -1 forces the fastest 'block' writing,
# value 0 writes each character separately without any explicite waiting,
# other positive values specify the appropriate 1/1000000 sec delaying.
# Siemens M20 requires at least "1"!  FIXME: Model-driven autodetection
#serial_write_usleep = 10000

# Force serial port handshaking mode, useful primarily for "AT" model.
# Gnokii "AT" model uses software handshake by default.
# Possible values: hardware (RTS/CTS - 7 wires) or software (XON/XOFF - 3 wires)
handshake = hardware

# If defined (not commented out by '#') it will quit Gnokii anytime
# when DCD line will drop.
#require_dcd = 1

# Run the specified script(s) right after opening and initializing the device
# and before any communucation (right before closing for disconnect_script).
# You may find handy to use it to connect your modem to SMS Center
# when using BIP or CIMD protocols
# Non-absolute path is relative to the specific directory where gnokii is run!
#connect_script = /absolute/path/to/gnokii/Docs/sample/cimd-connect
#disconnect_script =

# When sending SMS you can experience timeouts. This is the feature of the
# overloaded SMSCs. The phones waits for the response from the SMSC confirming
# that it received the short message. When the SMSC is DoSed with many requests
# it will take more time to get the response. Adjust it to your needs. The
# value is given in seconds to wait. Defaults to 10 seconds. Set to 0 to wait
# forever.
smsc_timeout = 10

# Any entries in the following two sections will be set as environment
# variables when running the scripts.
# Handy for use for $VAR substitutions in your chat(8) script.
[connect_script]
TELEPHONE = 12345678
[disconnect_script]