[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
Re: [Lilypond-auto] Issue 3944 in lilypond: Match PhrasingSlur thickness
From: |
lilypond |
Subject: |
Re: [Lilypond-auto] Issue 3944 in lilypond: Match PhrasingSlur thickness to Slur and Tie. |
Date: |
Mon, 09 Jun 2014 03:34:02 +0000 |
Comment #5 on issue 3944 by address@hidden: Match PhrasingSlur
thickness to Slur and Tie.
http://code.google.com/p/lilypond/issues/detail?id=3944
William Gamble:
p.101: "The lozenge graver has a more obtuse V-shape in the blade than the
tint graver. It is, in fact, in the form of a complete lozenge in section,
the lower of the two acute angles being used for the cutting. Naturally,
from its shape, it cuts a broader line than the tint graver, and the more
deeply it is forced into the metal, the more broadly it cuts. It is used
for engraving the slurs, for which the tool must enter lightly, penetrate
more deeply for the middle part of the curve, and run out lightly."
p.102: "Flat gravers have parallel sides, cutting like a chisel, so that
the line is of the same thickness as the tool, and the bottom of the cut is
flat. These tools are used for cutting the ties of the connected quavers.
Several sizes are required to suit the different sizes of notes, the ties
being thickened in proportion to the size."
p.107: "Whilst the employer usually provides the punches, the engraver
generally prefers to have a set of slur punches of his own, as they are not
expensive, rather than have to be constantly getting them from other
engravers who may be using them. There are about eleven sizes."
p.139: "The small slurs are punched, but the larger ones are cut with the
lozenge graver, although punches can be obtained for some of them."
p.148: "The ties are cut with scorpers (flat gravers), which have a flat
back. These vary in thickness according to the width to be cut, this
naturally depending on the size of the notes. The tool is given a slight
oscillatory movement by a turn of the wrist. This aids the tool in cutting
and gives to the bottom of the cut a waviness which helps retain the
printing ink."
p.149: "The large slurs are usually cut with the lozenge graver. Small
slurs are, however, generally punched. It is necessary in cutting a slur
with the graver to begin finely, pushing the blade first whilst it is held
level, then inclining it little by little, so that the cheeks of the tool
sink more and more deeply into the metal, thus forming the thick part of
the stroke, and finally, levelling the blade again, so as to finish with
the same fineness as at the beginning of the cut."
_____________________________________________
Ted Ross:
p.136: "Though ties, slurs, and phrase marks are constructed in basically
the same way, each performs a different function. [...] Plate engravers
punch dies into metal plates to achieve ties and short slurs. [...]
Longer ties are cut with a tool called the `graver'."
p.139: "The short slur is constructed in the same way as the tie, although
its function is entirely different."
p.140: "A long slur is a straight line with both ends bending uniformly
towards the enclosed notes." (nice examples on p.142)
_____________________________________________
Kurt Stone:
[he never specifically discusses the design or thickness of slurs, ties,
and phrase marks]
_____________________________________________
Elaine Gould:
p.60: "The tie and slur (phrase mark) have the same design, although ties
tend to have a flatter arc, to allow room for slurs and to differentiate
the two."
p.109: "The slur is the same tapered arc as the tie, although the tie may
have a flatter curve to allow room for slurs and to differentiate the two.
When notes at the beginning and end of a slur are the same pitch, the slur
may look identical to a tie because it will, like the tie,be completely
symmetrical."
p.113: [section labeled "Slurs within slurs" does not mention any change in
design, thickness, etc.]
--
You received this message because this project is configured to send all
issue notifications to this address.
You may adjust your notification preferences at:
https://code.google.com/hosting/settings
- [Lilypond-auto] Issue 3944 in lilypond: Match PhrasingSlur thickness to Slur and Tie., lilypond, 2014/06/06
- Re: [Lilypond-auto] Issue 3944 in lilypond: Match PhrasingSlur thickness to Slur and Tie., lilypond, 2014/06/07
- Re: [Lilypond-auto] Issue 3944 in lilypond: Match PhrasingSlur thickness to Slur and Tie., lilypond, 2014/06/07
- Re: [Lilypond-auto] Issue 3944 in lilypond: Match PhrasingSlur thickness to Slur and Tie., lilypond, 2014/06/08
- Re: [Lilypond-auto] Issue 3944 in lilypond: Match PhrasingSlur thickness to Slur and Tie., lilypond, 2014/06/08
- Re: [Lilypond-auto] Issue 3944 in lilypond: Match PhrasingSlur thickness to Slur and Tie.,
lilypond <=
- Re: [Lilypond-auto] Issue 3944 in lilypond: Match PhrasingSlur thickness to Slur and Tie., lilypond, 2014/06/11
- Re: [Lilypond-auto] Issue 3944 in lilypond: Match PhrasingSlur thickness to Slur and Tie., lilypond, 2014/06/11
- Re: [Lilypond-auto] Issue 3944 in lilypond: Match PhrasingSlur thickness to Slur and Tie., lilypond, 2014/06/14
- Re: [Lilypond-auto] Issue 3944 in lilypond: Match PhrasingSlur thickness to Slur and Tie., lilypond, 2014/06/17
- Re: [Lilypond-auto] Issue 3944 in lilypond: Match PhrasingSlur thickness to Slur and Tie., lilypond, 2014/06/17
- Re: [Lilypond-auto] Issue 3944 in lilypond: Match PhrasingSlur thickness to Slur and Tie., lilypond, 2014/06/18
- Re: [Lilypond-auto] Issue 3944 in lilypond: Match PhrasingSlur thickness to Slur and Tie., lilypond, 2014/06/18
- Re: [Lilypond-auto] Issue 3944 in lilypond: Match PhrasingSlur thickness to Slur and Tie., lilypond, 2014/06/20