I think you should do this in a seperate layout block, likt this:
\version "2.8.0"
\new StaffGroup \with{systemStartDelimiter = #'SystemStartBar } <<
\new PianoStaff <<
\new Staff \relative c' {c d e f }
\new Staff \relative c' {\clef bass c b a g }
>>
\new Staff \relative c {
\clef bass c1
}
\layout {
\context {
\Staff
\override VerticalAxisGroup #'minimum-Y-extent = #'(-6 . 6)
}
}
Hope this helps.
Best regards,
Bart Kummel, Hilversum, The Netherlands
On 4/9/06, MX <address@hidden> wrote:
---------- Forwarded message ----------
From: MX <address@hidden>
To: Mats Bengtsson <address@hidden>, address@hidden
Date: Sun, 09 Apr 2006 08:09:23 +0200
Subject: Re: The organ template works fine now but ....
Yhank you for your answers !
The new scheme you proposed is OK.
But I tried to tune interval between pedal stave et piano staves with :
* \override Staff.VerticalAxisGroup #'minimum-Y-extent = #'(-1 . 1)*
with no result. It changes extent between the groups of three staves but
non between the peadal stave and piano staves.
I varied the value (-1 . 1) with no result, I changes position of the
command \override. Where have I to place the command \override etc.
\new StaffGroup \with{systemStartDelimiter = #'SystemStartBar } <<
*here ?*
\new PianoStaff <<
*here ?*
\new Staff \relative c' {c d e f }
\new Staff \relative c' {\clef bass c b a g }
>>
*here ?*
\new Staff \relative c {\clef bass c1 }
>>
The syntax of the commands in general is confused and not completely
documented.
Thank you.
GG
Le 08.04.2006 20:19, :
> I don't think that helps, since PianoStaff sets a fixed
> spacing between its staves.
>
> I would recommend the following solution, which in a
> way is easier than what I initially proposed, namely to
> use a PianoStaff only for the manual staves and enclose
> all three staves in a GrandStaff. The only trick that's needed
> then is to get rid of the bracket, which is easy:
>
> \new StaffGroup \with{systemStartDelimiter = #'SystemStartBar } <<
> \new PianoStaff <<
> \new Staff \relative c' {c d e f }
> \new Staff \relative c' {\clef bass c b a g }
> >>
> \new Staff \relative c {\clef bass c1 }
> >>
>
>
> Now, you can change the minimum y extent of the
> pedal stave separately, if needed.
>
> /Mats
>
> Trevor Ba?a wrote:
>
>> have you tried minimum y extent?
>>
>> On 4/6/06, MX <address@hidden> wrote:
>>
>>
>>>
>>>
>>> ---------- Forwarded message ----------
>>> From: MX <address@hidden>
>>> To: Mats Bengtsson <address@hidden>
>>> Date: Thu, 06 Apr 2006 22:36:02 +0200
>>> Subject: The organ template works fine now but ...
>>> Thank you very much Mats, it works fine now.
>>>
>>> If someone asked you how to tune the distance between the pedal staff
>>> and the manuale staves, what would you answer ? I know someone who
>>> tried very hard with overrideProperty commands, VerticalAlignment etc.
>>> and who did not manage to do anything...
>>>
>>> M.X.
>>>
>>> Le 05.04.2006 20:09, :
>>>
>>>
>>>
>>>> Simple, just replace StaffGroup by PianoStaff.
>>>>
>>>> /Mats
>>>>
>>>> GG wrote:
>>>>
>>>>
>>>>
>>>>> Unfortunately, it seems that this solution doesn't authorize the
>>>>> staff changes between the manuale staves, as in the Pianostaff
>>>>> command.
>>>>>
>>>>> M.X.
>>>>>
>>>>
>>>>
>>>>
>>>>
>>>
>>>
>>>
>>>
>>>
>>> _______________________________________________
>>> lilypond-user mailing list
>>> address@hidden
>>> http://lists.gnu.org/mailman/listinfo/lilypond-user
>>>
>>>
>>>
>>>
>>
>>
>>
>> --
>> Trevor Ba?a
>> address@hidden
>>
>>
>>
------------------------------------------------------------------------
>>
>> _______________________________________________
>> lilypond-user mailing list
>> address@hidden
>> http://lists.gnu.org/mailman/listinfo/lilypond-user
>>
>>
>
>
_______________________________________________
lilypond-user mailing list
address@hidden
http://lists.gnu.org/mailman/listinfo/lilypond-user