Re :Re: [Ltib] ltib error -linux2.6.20.6 with MPC8360E MDS

[nanda]

Hi Stuart,
   Thanks for the information.   gpp access was resolved. 
   I was successful in building the linux 2.6.11 using the ltib and able to bring up the MPC8360 EMDS.
But, I still face the problem for linux kernel 2.6.19 and 2.6.20.   When I tried using ltib in the bringing up the board. 
  The MPC 8360 board keeps rebooting after downloading the image Power PC Kernel Image(uImage) and Power PC RAMDisk Image(rootfs.ext2.gz.uboot)  build by the "ltib" 
    Please clarrify on the same.

Thanks in advance.

Regards,
Nanda

 

 
On Thu, 20 Nov 2008 18:40:36 0000 Stuart Hughes wrote
Hi Nanda,

This is happening because you don't have access to
http://www.bitshrine.org/gpp for some reason.

If LTIB needs to download sources to build a package, it will get them
from bitshrine.org. Can you check that you are able to access this URL
from the command line with wget.

Regards, Stuart

On Thu, 2008-11-20 at 18:30 0000, nanda wrote:
> Hi All,
> Iam forwarding the mail which I have posted to powerpc linux list
> address@hidden
> ===================================================
> 
> Iam getting the below error during the generation of
> rootfs.ext2.gz.uboot (Power PC Linux RAM Disk Image) and uImage (Power
> PC Linux Kernel Image) for linux-2.6.20.6 kernel on the power PC MPC
> 8360E MDS using ltib tool.
> 
> "Testing ppp_url connectivity: FAIL, disabling 
> 
> Testing gpp_url connectivity: FAIL, disabling 
> 
> No network download connection available"
> 
> I did the following steps, but Iam unable to generate the
> rootfs.ext2.gz.uboot 
> 
> - In the ltib directory 
> 
> ./ltib --configure
> 
> In the configure menu, I specified the following, before saving the
> configs
> 
> - Tool chain as (gcc-3.4.3/glibc-2.3.3)
> 
> - uboot 1.1.3
> 
> - "Kernel (local linux directory build)" which refers to the local
> directory where linux-2.6.20.6 is placed
> 
> - "Kernel config file"specified as mpc8360emds_defconfig, which is the
> file copied
> from /home/nanda/linux2.6.20.6/arch/powerpc/configs/mpc8360emds_defconfig to the ltib/config/platform/mpc8360epb directory) 
> 
> - Linux Target Architecture as "powerpc"
> 
> After the above process by saving the configuration (it started
> building kernel and generated uImage) and failed in the below place
> (Refer also the attached build.txt file)
> 
> ================================
> 
> Processing: skell 
> 
> =================== 
> 
> Testing ppp_url connectivity: FAIL, disabling 
> 
> Testing gpp_url connectivity: FAIL, disabling 
> 
> No network download connection available
> 
> Started: Thu Nov 20 14:44:45 2008 
> 
> Ended: Thu Nov 20 14:57:32 2008 
> 
> Elapsed: 767 seconds 
> 
> Build Failed
> 
> =====================================
> 
> I have attached the below files for boot and build logs with this
> mail, 
> 
> 1) defconfig.dev - default config generated for "./ltib configure"
> from config/platform/mpc8360epb 
> 
> 2) build.txt - Error build during "./ltib configure" output
> 
> 3) mpc8360emds_defconfig - Default config file
> from /home/nanda/linux2.6.20.6/arch/powerpc/configs/ 
> 
> The end result was I could only see the uImage generated without
> rootfs.ext2.gz.uboot. Please clarify on the same 
> 
> Thanks in advance,
> 
> Regards,
> 
> Nanda
> 


_______________________________________________
Linuxppc-dev mailing list
address@hidden
https://ozlabs.org/mailman/listinfo/linuxppc-dev