Phytec LPC3250 board Build date: Dec 4 2008 09:45:09 Autoboot in progress, press any key to stop.. U-Boot 1.3.3 (Apr 10 2009 - 09:21:30) DRAM: 64 MB NAND: 64 MiB In: serial Out: serial Err: serial Hit any key to stop autoboot: 1  0 HW MAC address: 00:50:C2:B6:A8:D9 ENET:auto-negotiation complete ENET:Link status up ENET:FULL DUPLEX ENET:100MBase TFTP from server 10.10.20.70; our IP address is 10.10.20.88 Filename 'uImage'. Load address: 0x80100000 Loading: *################################################################# ############################################# done Bytes transferred = 1611088 (189550 hex) ## Booting kernel from Legacy Image at 80100000 ... Image Name: Linux-2.6.27.8 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 1611024 Bytes = 1.5 MB Load Address: 80008000 Entry Point: 80008000 Verifying Checksum ... OK Loading Kernel Image ... OK OK Starting kernel ... Uncompressing Linux............................................................................ done, booting the kernel. ÿLinux version 2.6.27.8 (address@hidden) (gcc version 4.1.2) #34 PREEMPT Tue Jul 13 11:15:28 EST 2010 CPU: ARM926EJ-S [41069264] revision 4 (ARMv5TEJ), cr=00053177 Machine: Phytec 3250 board with the LPC3250 Microcontroller Memory policy: ECC disabled, Data cache writeback CPU0: D VIVT write-back cache CPU0: I cache: 32768 bytes, associativity 4, 32 byte lines, 256 sets CPU0: D cache: 32768 bytes, associativity 4, 32 byte lines, 256 sets Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256 Kernel command line: console=ttyS0,115200n81 root=/dev/nfs rw nfsroot=10.10.20.70:/home/q.yang/lpc3250/ltib-qs/rootfs ip=10.10.20.88 init=/sbin/init PID hash table entries: 256 (order: 8, 1024 bytes) Console: colour dummy device 80x30 Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) Memory: 64MB = 64MB total Memory: 61524KB available (2988K code, 241K data, 100K init) Calibrating delay loop... 103.68 BogoMIPS (lpj=207360) Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok net_namespace: 288 bytes NET: Registered protocol family 16 Hardware descriptor info: DRAM config word: 0x00000008 syscfg word: 0x00000001 fieldval word: 0x000a3250 MAC address: <6>00:50:c2:b6:a8:d9 LPC32XX DMA driver LPC32XX unique ID: 0005d71b1170000007a4901850ccb400 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 2048 (order: 2, 16384 bytes) TCP bind hash table entries: 2048 (order: 1, 8192 bytes) TCP: Hash tables configured (established 2048 bind 2048) TCP reno registered NET: Registered protocol family 1 NetWinder Floating Point Emulator V0.97 (double precision) JFFS2 version 2.2. (NAND) © 2001-2006 Red Hat, Inc. msgmni has been set to 120 io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) Serial: 8250/16550 driver4 ports, IRQ sharing disabled serial8250.0: ttyS0 at MMIO 0x40090000 (irq = 9) is a 16550A console [ttyS0] enabled loop: module loaded LPC32XX_mii_bus: probed eth0: LPC32XX mac at 0x31060000 irq 29 eth0: attached PHY driver [SMSC LAN8700] (mii_bus:phy_addr=0:00, irq=-1) Driver 'sd' needs updating - please use bus_type methods NAND device: Manufacturer ID: 0x20, Chip ID: 0x36 (ST Micro NAND 64MiB 1,8V 8-bit) Scanning device for bad blocks Bad eraseblock 2493 at 0x026f4000 Creating 4 MTD partitions on "lpc32xx_nand": 0x00000000-0x00168000 : "phy3250-boot" 0x00168000-0x00190000 : "phy3250-ubt-prms" 0x00190000-0x00590000 : "phy3250-kernel" 0x00590000-0x04000000 : "phy3250-rootfs" at25 spi0.0: 32 KByte at25256a eeprom, pagesize 64 usbmon: debugfs is not available I2C device at address 0x2c<6>ISP1301 Vendor ID : 0x04cc ISP1301 Product ID : 0x1301 ISP1301 Version ID : 0x0210 usb-ohci usb-ohci: at 0xf3120000, irq 0 usb-ohci usb-ohci: pnx4008 OHCI usb-ohci usb-ohci: new USB bus registered, assigned bus number 1 usb-ohci usb-ohci: irq 59, io mem 0xf3120000 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected usb usb1: New USB device found, idVendor=1d6b, idProduct=0001 usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb1: Product: pnx4008 OHCI usb usb1: Manufacturer: Linux 2.6.27.8 ohci_hcd usb usb1: SerialNumber: usb-ohci Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. usbcore: registered new interface driver libusual rtc-lpc32xx rtc-lpc32xx: rtc core: registered rtc-lpc32xx as rtc0 i2c /dev entries driver PNX4008-WDT: PNX4008 Watchdog Timer: heartbeat 19 sec mmci-pl18x: DMA buffer(10000 bytes), P:0x83960000, V:0xffc1c000 mmc0: MMCI rev 0 cfg 00 at 0x0000000020098000 irq 15,13 usbcore: registered new interface driver usbhid usbhid: v2.6:USB HID core driver TCP cubic registered NET: Registered protocol family 17 RPC: Registered udp transport module. RPC: Registered tcp transport module. ieee80211: 802.11 data/management/control stack, git-1.1.13 ieee80211: Copyright (C) 2004-2005 Intel Corporation VFP support v0.3: implementor 41 architecture 1 part 10 variant 9 rev 1 rtc-lpc32xx rtc-lpc32xx: setting system clock to 2006-03-17 02:09:38 UTC (1142561378) mmc0: host does not support reading read-only switch. assuming write-enable. mmc0: new SD card at address b368 mmcblk0: mmc0:b368 SD 1981440KiB mmcblk0: IP-Config: Guessing netmask 255.0.0.0 IP-Config: Complete: device=eth0, addr=10.10.20.88, mask=255.0.0.0, gw=255.255.255.255, host=10.10.20.88, domain=, nis-domain=(none), bootserver=255.255.255.255, rootserver=10.10.20.70, rootpath= Looking up port of RPC 100003/2 on 10.10.20.70 Looking up port of RPC 100005/1 on 10.10.20.70 VFS: Mounted root (nfs filesystem). Freeing init memory: 100K init started: BusyBox v1.11.2 () starting pid 269, tty '': '/etc/rc.d/rcS' Mounting /proc and /sys Starting the hotplug events dispatcher mdev Setting the hostname to GsnCommsModule [-m ] [options....] Mounting filesystems Starting syslogd and klogd Running sysctl Setting up networking on loopback device: Warning: no IPADDR is set, please set this from the ltib config screen, or directly in /etc/rc.d/rc.conf. IP address setup bypassed Setting up networking on eth1: ifconfig: SIOCSIFADDR: No such device Adding static route for default gateway to 10.10.10.1: route: SIOCADDRT: No such device Setting nameserver to 10.10.10.1 in /etc/resolv.conf: Starting the ssh server: starting pid 350, tty '': '-/bin/sh' address@hidden /]# usb 1-1: new full speed USB device using usb-ohci and address 2 usb 1-1: configuration #1 chosen from 1 choice usb 1-1: New USB device found, idVendor=1199, idProduct=683c usb 1-1: New USB device strings: Mfr=3, Product=2, SerialNumber=0 usb 1-1: Product: Mini Card usb 1-1: Manufacturer: Sierra Wireless, Incorporated address@hidden /]#ls /dev 1-1 tty0 tty45 console tty1 tty46 cpu_dma_latency tty10 tty47 full tty11 tty48 i2c-0 tty12 tty49 i2c-2 tty13 tty5 kmem tty14 tty50 kmsg tty15 tty51 log tty16 tty52 loop0 tty17 tty53 loop1 tty18 tty54 loop2 tty19 tty55 loop3 tty2 tty56 loop4 tty20 tty57 loop5 tty21 tty58 loop6 tty22 tty59 loop7 tty23 tty6 mem tty24 tty60 mmcblk0 tty25 tty61 mtd0 tty26 tty62 mtd0ro tty27 tty63 mtd1 tty28 tty7 mtd1ro tty29 tty8 mtd2 tty3 tty9 mtd2ro tty30 ttyS0 mtd3 tty31 ttyS1 mtd3ro tty32 ttyS2 mtdblock0 tty33 ttyS3 mtdblock1 tty34 urandom mtdblock2 tty35 usbdev1.1 mtdblock3 tty36 usbdev1.1_ep00 network_latency tty37 usbdev1.1_ep81 network_throughput tty38 usbdev1.2 null tty39 usbdev1.2_ep00 ptmx tty4 usbdev1.2_ep01 pts tty40 usbdev1.2_ep81 random tty41 vcs rtc0 tty42 vcsa shm tty43 watchdog tty tty44 zero address@hidden /]# lsmod Module Size Used by Not tainted address@hidden /]# insmod usbserial.ko usbcore: registered new interface driver usbserial usbserial: USB Serial support registered for generic usbcore: registered new interface driver usbserial_generic usbserial: USB Serial Driver core address@hidden /]# insmod sierra.ko usbserial: USB Serial support registered for Sierra USB modem sierra 1-1:1.0: Sierra USB modem converter detected usb 1-1: Sierra USB modem converter now attached to ttyUSB0 usbcore: registered new interface driver sierra sierra: sierra version: v.1.7.32 address@hidden /]# ls /dev 1-1 tty1 tty47 console tty10 tty48 cpu_dma_latency tty11 tty49 full tty12 tty5 i2c-0 tty13 tty50 i2c-2 tty14 tty51 kmem tty15 tty52 kmsg tty16 tty53 log tty17 tty54 loop0 tty18 tty55 loop1 tty19 tty56 loop2 tty2 tty57 loop3 tty20 tty58 loop4 tty21 tty59 loop5 tty22 tty6 loop6 tty23 tty60 loop7 tty24 tty61 mem tty25 tty62 mmcblk0 tty26 tty63 mtd0 tty27 tty7 mtd0ro tty28 tty8 mtd1 tty29 tty9 mtd1ro tty3 ttyS0 mtd2 tty30 ttyS1 mtd2ro tty31 ttyS2 mtd3 tty32 ttyS3 mtd3ro tty33 ttyUSB0 mtdblock0 tty34 urandom mtdblock1 tty35 usbdev1.1 mtdblock2 tty36 usbdev1.1_ep00 mtdblock3 tty37 usbdev1.1_ep81 network_latency tty38 usbdev1.2 network_throughput tty39 usbdev1.2_ep00 null tty4 usbdev1.2_ep01 ptmx tty40 usbdev1.2_ep81 pts tty41 vcs random tty42 vcsa rtc0 tty43 watchdog shm tty44 zero tty tty45 tty0 tty46 address@hidden /]# usb 1-1: USB disconnect, address 2 sierra ttyUSB0: Sierra USB modem converter now disconnected from ttyUSB0 sierra 1-1:1.0: device disconnected address@hidden /]#ls /dev console tty0 tty44 cpu_dma_latency tty1 tty45 full tty10 tty46 i2c-0 tty11 tty47 i2c-2 tty12 tty48 kmem tty13 tty49 kmsg tty14 tty5 log tty15 tty50 loop0 tty16 tty51 loop1 tty17 tty52 loop2 tty18 tty53 loop3 tty19 tty54 loop4 tty2 tty55 loop5 tty20 tty56 loop6 tty21 tty57 loop7 tty22 tty58 mem tty23 tty59 mmcblk0 tty24 tty6 mtd0 tty25 tty60 mtd0ro tty26 tty61 mtd1 tty27 tty62 mtd1ro tty28 tty63 mtd2 tty29 tty7 mtd2ro tty3 tty8 mtd3 tty30 tty9 mtd3ro tty31 ttyS0 mtdblock0 tty32 ttyS1 mtdblock1 tty33 ttyS2 mtdblock2 tty34 ttyS3 mtdblock3 tty35 urandom network_latency tty36 usbdev1.1 network_throughput tty37 usbdev1.1_ep00 null tty38 usbdev1.1_ep81 ptmx tty39 vcs pts tty4 vcsa random tty40 watchdog rtc0 tty41 zero shm tty42 tty tty43 address@hidden /]#