Re: [lwip-users] [EXTERNAL MAIL]Re: very poor performance of httpd

[Sachs, Nico]

You may have seen my message from yesterday, those extra printfs give the 
needed delays before the packets gets sent out. 

Cheers

-----Ursprüngliche Nachricht-----
Von: lwip-users <lwip-users-bounces+nico.sachs=trumpf.com@nongnu.org> Im 
Auftrag von Felix Frey
Gesendet: Dienstag, 18. August 2020 16:17
An: lwip-users@nongnu.org
Betreff: [EXTERNAL MAIL]Re: [lwip-users] very poor performance of httpd

On further investigation on this, I've found an interesting fact.
Any changes in the lwip's configuration didn't cause a change, however, when I 
enabled MEMP_DEBUG the problem was gone, no more of this strange "Trying to 
send 0 bytes" occurencies and the httpd responded fast and as expected.
Of course this isn't a real solution because lwip generates lots of messages 
when memp_debug is enabled. Anyway, it seems the problem is not inside the 
httpd but maybe deeper.
I really appreciate if anybody has an idea what could be the relation.

Felix

Am 17.08.20 um 16:28 schrieb Mário Luzeiro:
> Hi Felix,
> 
> I had similar issues but using TLS
> https://lists.nongnu.org/archive/html/lwip-users/2020-05/msg00006.html
> 
> I experience the same: some requests are very quick and others take seconds.
> ..but didn't found a solution yet.
> 
> I will follow this thread in case someone comes with more suggestions.
> 
> I suggest you can start trying to increase MEMP_NUM_TCP_PCB to the 
> double I think play with smaller values in TCP_MSS and/or TCP_WND could 
> help.. but not sure...
> 
> Mario
> 
> ________________________________________
> From: lwip-users <lwip-users-bounces+mrluzeiro=ua.pt@nongnu.org> on 
> behalf of Felix Frey <frey@stettbacher.ch>
> Sent: 17 August 2020 14:40
> To: lwip-users@nongnu.org
> Subject: [lwip-users] very poor performance of httpd
> 
> Hi,
> 
> I've running an application on a STM32F429 using LwIP 2.0.3 and it's httpd.
> Basically it works fine, however the performance of the httpd is very poor.
> 
> When the browser does a http request for a total of five files 
> (statically linked) with a total amount of 40kB, it takes about 5sec to 
> complete the request.
> It seems like the httpd gets stalled.
> In the log I can see several of the entrys below:
> -----
> 00006.560: http_poll: pcb=0x2000d7b8 hs=0x2000db08 
> pcb_state=ESTABLISHED
> 00006.560: http_poll: try to send more data
> 00006.560: http_send: hs=0x2000db08 pcb=0x2000d7b8 left=22030
> 00006.560: Trying to send 0 bytes
> 00006.560: Sent 0 bytes
> 00006.560: send_data end.
> 00006.560: tcp_output
> -----
> This is repeated every 500ms for about 2sec until sending moves on.
> It looks like it simply doesn't anything during this time. Why??
> 
> My memory settings are:
> #define MEM_LIBC_MALLOC 1
> #define MEMP_NUM_TCP_PCB 8
> #define MEMP_NUM_PBUF 32
> #define TCP_MSS 1460
> #define TCP_WND 2920
> 
> I've already played with configuration settings, however, it didn't change a 
> lot.
> Can anybody explain this behaviour or even help to improve it?
> 
> Thanks in advance.
> Felix
> 
> _______________________________________________
> lwip-users mailing list
> lwip-users@nongnu.org
> https://lists.nongnu.org/mailman/listinfo/lwip-users
> 
> _______________________________________________
> lwip-users mailing list
> lwip-users@nongnu.org
> https://lists.nongnu.org/mailman/listinfo/lwip-users
> 

--
Felix Frey
Stettbacher Signal Processing
Neugutstrasse 54
CH-8600 Dübendorf, Switzerland
Fon +41 43 299 57 23
frey@stettbacher.ch
http://www.stettbacher.ch

_______________________________________________
lwip-users mailing list
lwip-users@nongnu.org
https://lists.nongnu.org/mailman/listinfo/lwip-users