[paparazzi-commits] [4887]

[antoine drouin]

Revision: 4887
          http://svn.sv.gnu.org/viewvc/?view=rev&root=paparazzi&revision=4887
Author:   poine
Date:     2010-04-27 18:57:01 +0000 (Tue, 27 Apr 2010)
Log Message:
-----------


Added Paths:
-----------
    paparazzi3/trunk/sw/airborne/lisa/arch/
    paparazzi3/trunk/sw/airborne/lisa/arch/stm32/
    paparazzi3/trunk/sw/airborne/lisa/arch/stm32/lisa_overo_link_arch.c

Added: paparazzi3/trunk/sw/airborne/lisa/arch/stm32/lisa_overo_link_arch.c
===================================================================
--- paparazzi3/trunk/sw/airborne/lisa/arch/stm32/lisa_overo_link_arch.c         
                (rev 0)
+++ paparazzi3/trunk/sw/airborne/lisa/arch/stm32/lisa_overo_link_arch.c 
2010-04-27 18:57:01 UTC (rev 4887)
@@ -0,0 +1,102 @@
+#include "lisa/lisa_overo_link.h"
+
+#include <stm32/rcc.h>
+#include <stm32/gpio.h>
+#include <stm32/flash.h>
+#include <stm32/misc.h>
+#include <stm32/spi.h>
+#include <stm32/dma.h>
+
+void dma1_c2_irq_handler(void);
+
+void overo_link_arch_init(void) {
+ 
+  /* Enable SPI_1 DMA clock 
---------------------------------------------------*/
+  RCC_AHBPeriphClockCmd(RCC_AHBPeriph_DMA1, ENABLE);
+  /* Enable SPI1 Periph clock 
-------------------------------------------------*/
+  RCC_APB2PeriphClockCmd(RCC_APB2Periph_SPI1, ENABLE);
+  /* Configure GPIOs: NSS, SCK, MISO and MOSI  
--------------------------------*/
+  GPIO_InitTypeDef GPIO_InitStructure;
+  GPIO_InitStructure.GPIO_Pin = GPIO_Pin_4 | GPIO_Pin_5 | GPIO_Pin_6 | 
GPIO_Pin_7;
+  GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
+  GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;
+  GPIO_Init(GPIOA, &GPIO_InitStructure);
+  /* SPI_SLAVE configuration 
--------------------------------------------------*/
+  SPI_InitTypeDef SPI_InitStructure;
+  SPI_InitStructure.SPI_Direction = SPI_Direction_2Lines_FullDuplex;
+  SPI_InitStructure.SPI_Mode = SPI_Mode_Slave;
+  SPI_InitStructure.SPI_DataSize = SPI_DataSize_8b;
+  SPI_InitStructure.SPI_CPOL = SPI_CPOL_Low;
+  SPI_InitStructure.SPI_CPHA = SPI_CPHA_2Edge;
+  SPI_InitStructure.SPI_NSS = SPI_NSS_Hard;
+  SPI_InitStructure.SPI_BaudRatePrescaler = SPI_BaudRatePrescaler_4;
+  SPI_InitStructure.SPI_FirstBit = SPI_FirstBit_MSB;
+  SPI_InitStructure.SPI_CRCPolynomial = 7;
+  SPI_Init(SPI1, &SPI_InitStructure); 
+  /* Enable SPI_SLAVE */
+  SPI_Cmd(SPI1, ENABLE);
+
+  /* Configure DMA1 channel2 IRQ Channel */
+  NVIC_InitTypeDef NVIC_init_struct = {
+    .NVIC_IRQChannel = DMA1_Channel2_IRQn,
+    .NVIC_IRQChannelPreemptionPriority = 0,
+    .NVIC_IRQChannelSubPriority = 0,
+    .NVIC_IRQChannelCmd = ENABLE 
+  };
+  NVIC_Init(&NVIC_init_struct);
+
+  /* setup DMA for first transfert */
+  overo_link_arch_prepare_next_transfert();
+  
+
+}
+
+
+void overo_link_arch_prepare_next_transfert(void) {
+
+  /* SPI_SLAVE_Rx_DMA_Channel configuration 
------------------------------------*/
+  DMA_InitTypeDef  DMA_InitStructure;                                  
+  DMA_DeInit(DMA1_Channel2);                                           
+  DMA_InitStructure.DMA_PeripheralBaseAddr = (uint32_t)(SPI1_BASE+0x0C); 
+  DMA_InitStructure.DMA_MemoryBaseAddr = (uint32_t)&(overo_link.msg_in);
+  DMA_InitStructure.DMA_DIR = DMA_DIR_PeripheralSRC;                   
+  DMA_InitStructure.DMA_BufferSize = sizeof(overo_link.msg_in);                
        
+  DMA_InitStructure.DMA_PeripheralInc = DMA_PeripheralInc_Disable;     
+  DMA_InitStructure.DMA_MemoryInc = DMA_MemoryInc_Enable;              
+  DMA_InitStructure.DMA_PeripheralDataSize = DMA_PeripheralDataSize_Byte;
+  DMA_InitStructure.DMA_MemoryDataSize = DMA_MemoryDataSize_Byte;      
+  DMA_InitStructure.DMA_Mode = DMA_Mode_Normal;                        
+  DMA_InitStructure.DMA_Priority = DMA_Priority_VeryHigh;              
+  DMA_InitStructure.DMA_M2M = DMA_M2M_Disable;                 
+  DMA_Init(DMA1_Channel2, &DMA_InitStructure);                 
+
+  /* SPI_SLAVE_Tx_DMA_Channel configuration 
------------------------------------*/
+  DMA_DeInit(DMA1_Channel3);  
+  DMA_InitStructure.DMA_PeripheralBaseAddr = (uint32_t)(SPI1_BASE+0x0C);
+  DMA_InitStructure.DMA_MemoryBaseAddr = (uint32_t)&(overo_link.msg_out);
+  DMA_InitStructure.DMA_DIR = DMA_DIR_PeripheralDST;
+  DMA_InitStructure.DMA_Priority = DMA_Priority_Medium;
+  DMA_Init(DMA1_Channel3, &DMA_InitStructure);
+  
+  /* Enable SPI_1 Rx request */
+  SPI_I2S_DMACmd(SPI1, SPI_I2S_DMAReq_Rx, ENABLE);
+  /* Enable DMA1 Channel2 */
+  DMA_Cmd(DMA1_Channel2, ENABLE);
+  /* Enable SPI_1 Rx request */
+  SPI_I2S_DMACmd(SPI1, SPI_I2S_DMAReq_Tx, ENABLE);
+  /* Enable DMA1 Channel3 */
+  DMA_Cmd(DMA1_Channel3, ENABLE);
+
+  /* Enable DMA1 Channel2 Transfer Complete interrupt */
+  DMA_ITConfig(DMA1_Channel2, DMA_IT_TC, ENABLE);
+
+}
+
+
+void dma1_c2_irq_handler(void) {
+
+  DMA_ITConfig(DMA1_Channel2, DMA_IT_TC, DISABLE);
+
+  overo_link.status = DATA_AVAILABLE;
+}
+