paparazzi-devel
[Top][All Lists]
Advanced

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: [Paparazzi-devel] execution


From: Felix Ruess
Subject: Re: [Paparazzi-devel] execution
Date: Mon, 14 Jun 2010 20:55:14 +0200

Roman,

I meant in the messages tool... (Tools -> messages)
Your Xbees are not correctly set up it seems.
Stick with one airframe and REALLY make sure your xbee baud rate
settings are correct.

Felix

On Mon, Jun 14, 2010 at 8:48 PM, Roman Nikitin <address@hidden> wrote:
> Felix,
>
> no, I have no messages in my GCS window which opens after I push the button 
> "execute". Just a black window as I described before. I tried to flash 
> another aircrafts they also didn't work. I have no idea where the problem is. 
> The wires seems to be not damaged and the connections are also proved, 
> everything on the places. The single point worrying me is that the "data In" 
> light on the stand-alone modem (with usb connection) is never blinking. It 
> means no incoming data to the stand-alone modem from air-born modem (board).
>
> Tomorrow I can try to prove the wires on the signals.
>
> I can´t believe that just me have such kind of problem.
>
> GUYS, some ideas?
>
> Regards,
>
> Roman
>
>
> -----Ursprüngliche Nachricht-----
> Von: address@hidden [mailto:address@hidden Im Auftrag von Felix Ruess
> Gesendet: Montag, 14. Juni 2010 18:35
> An: address@hidden
> Betreff: Re: [Paparazzi-devel] execution
>
> Roman,
>
>> message tool says that everything is running.
>
> so you can see the messages coming in and changing, lots of green
> blinking thingies?
>
>> The modems were set up to 9600 baud rate. The data in airframe file looks 
>> like this
>>
>> ap.CFLAGS += -DDOWNLINK -DUSE_UART1 -DDOWNLINK_TRANSPORT=PprzTransport 
>> -DDOWNLINK_FBW_DEVICE=Uart1 -DDOWNLINK_AP_DEVICE=Uart1 -DPPRZ_UART=Uart1 
>> -DDATALINK=PPRZ -DUART1_BAUD=B9600
>>
>> ap.CFLAGS += -DGPS -DUBX -DUSE_UART0 -DGPS_LINK=Uart0 -DUART0_BAUD=B38400
>>
>> I tried to change the baud from 38400 to 9600, but it is still not working.
>
> You should be fine with 9600 baud then...
> The GPS is configured for 38400 baud as you can see in the last line...
>
>> The same picture as I described it before. As I tried to load google map I 
>> got the error
>> Thread 1 killed on uncaught exception Failure("#of_world:no georef")
>
> It seems you still don't get messages in the gcs, are you really sure?
>
>> My sensors and my GPS are not arranged yet. Can it influence the process?
>
> No.
>
>
>> -----Ursprüngliche Nachricht-----
>> Von: address@hidden [mailto:address@hidden Im Auftrag von Felix Ruess
>> Gesendet: Montag, 14. Juni 2010 16:39
>> An: address@hidden
>> Betreff: Re: [Paparazzi-devel] execution
>>
>> Roman,
>>
>> check with the messages tool if you receive any messages.
>> But it sounds like your xbee configuration on the aircraft side is
>> wrong, maybe wrong baud rate? Check that the baudrate in the airframe
>> file you flashed matches the one you set your aircraft side xbee to.
>>
>> Felix
>>
>>
>>
>> _______________________________________________
>> Paparazzi-devel mailing list
>> address@hidden
>> http://lists.nongnu.org/mailman/listinfo/paparazzi-devel
>>
>
> _______________________________________________
> Paparazzi-devel mailing list
> address@hidden
> http://lists.nongnu.org/mailman/listinfo/paparazzi-devel
>
>
> _______________________________________________
> Paparazzi-devel mailing list
> address@hidden
> http://lists.nongnu.org/mailman/listinfo/paparazzi-devel
>



reply via email to

[Prev in Thread] Current Thread [Next in Thread]