paparazzi-devel
[Top][All Lists]
Advanced

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

AW: [Paparazzi-devel] GPS flashing


From: Roman Nikitin
Subject: AW: [Paparazzi-devel] GPS flashing
Date: Fri, 9 Jul 2010 12:12:35 +0100

Thank you for advise, Maik. I will try to do it. 

Roman

-----Ursprüngliche Nachricht-----
Von: address@hidden [mailto:address@hidden Im Auftrag von Maik Höpfel
Gesendet: Freitag, 9. Juli 2010 09:54
An: address@hidden
Betreff: Re: [Paparazzi-devel] GPS flashing

Autopilot on is enough. The tunnel does what the name implies, it just
transparently passes any incoming messages to the GPS. Just in case
your Xbees give you more trouble, I think you can also program it via
USB cable just as you do for flashing, read up on the wiki for that.

- Maik

2010/7/9 Roman Nikitin <address@hidden>:
> Felix,
>
> I don´t have any FTDI cable. So you mean I need to download a tunnel first, 
> and then it works through the xbees. Is it correct? And while I am doing 
> this, as I can see, the GCS should be running. Or not? Or it is enough if the 
> autopilot is powered only and xbees connected?
>
> Thank you.
>
> Roman
>
>
>  Nachricht-----
> Von: address@hidden [mailto:address@hidden Im Auftrag von Felix Ruess
> Gesendet: Donnerstag, 8. Juli 2010 22:08
> An: address@hidden
> Betreff: Re: [Paparazzi-devel] GPS flashing
>
> If you have an FTDI cable you can also just directly connect the GPS,
> you don't need to go through the autopilot. But using the tunnel can
> be very convenient since you can also just use your already connected
> xbees instead of the serial cable.
>
> Felix
>
> 2010/7/8 C.KUO <address@hidden>:
>> Hi
>>
>>
>>  I assume you use Tiny V2 or TWOG, first you need upload "tunnel" to your
>> board though usb (in the paparazzi center, select the new target, and press
>> build then upload)
>>
>>  Then connect your FTDI cable to serial port on the Tiny (where the modem is
>> connect to), then you can start us Ublox software to flash your GPS.
>>
>>
>>  I hope these helps
>>
>>
>> Regards
>>
>>                                                                       Chen
>>
>>
>> 引述 Roman Nikitin <address@hidden>:
>>
>>> Hi,
>>>
>>>
>>>
>>> to flash the GPS, can I use the serial connection or it should be done on
>>> the same way I flashed my ap board?
>>>
>>>
>>>
>>> Sorry guys, a lot of questions from my side today. I am really in hurry.
>>>
>>>
>>>
>>> Thanks.
>>>
>>>
>>>
>>> Roman
>>>
>>>
>>>
>>>
>>>
>>> Bristol Institute of Technology
>>>
>>> University of the West of England
>>>
>>> Aerospace Systems Engineering
>>>
>>> email: address@hidden
>>>
>>> Mob.: +44 (0) 7760806643
>>>
>>>
>>>
>>>
>>
>>
>>
>> C.KUO
>> Aerospace Engineering, MEng
>> Mechanical Engineering, PhD
>> Research Associate
>> Department of Materials Science and Engineering
>> Saarland University
>> Campus Dudweiler
>> Am Markt - Zeile 4
>> 66125 Saarbrucken, Germany
>> Tel.: +49 (0) 681 - 302 64197
>> Fax: +49 (0) 681 - 9302 5934
>>
>>
>> _______________________________________________
>> Paparazzi-devel mailing list
>> address@hidden
>> http://lists.nongnu.org/mailman/listinfo/paparazzi-devel
>>
>
> _______________________________________________
> Paparazzi-devel mailing list
> address@hidden
> http://lists.nongnu.org/mailman/listinfo/paparazzi-devel
>
>
> _______________________________________________
> Paparazzi-devel mailing list
> address@hidden
> http://lists.nongnu.org/mailman/listinfo/paparazzi-devel
>

_______________________________________________
Paparazzi-devel mailing list
address@hidden
http://lists.nongnu.org/mailman/listinfo/paparazzi-devel




reply via email to

[Prev in Thread] Current Thread [Next in Thread]