Re: [Paparazzi-devel] Problems getting an overview of Paparazzi

[Gareth Roberts]

Hi Christian,

None of your current hardware will be much use I'm afraid.

You need the autopilot unit itself which is called a Tiny.  This goes in  
the aircraft.
http://paparazzi.enac.fr/wiki/Tiny_v2#Architecture

You can't stabilise a UAV via the ground, there is too much latency.
The paparazzi board (Tiny) does all the work, the ground station simply  
displays what is going on and allows changing high level flight parameters  
(current waypoint etc).

If this is your first UAV project, forget the gyro - Paparazzi  
traditionally uses infra-red level sensors, which are described on the  
wiki.

Have any of you got experience with model aircraft?  You will need someone  
who is competent at flying model aircraft.  Your Twinstar should be fine.   
You almost certainly do not want to build your own Tiny board - I would  
highly recommend purchasing from one of the suppliers, listed on the wiki.

An example of everything you need is here (I'm not promoting this  
particular supplier, they are just the only one I'm currently aware of  
with a photo of all the stuff you need!):
https://mini.ppzuav.com/osc/product_info.php?cPath=2&products_id=68&osCsid=jug5m75orjn3rvq182qhmq8vfaquggjc

Also, read getting started on the wiki:
http://paparazzi.enac.fr/wiki/Getting_Started

I would recommend maybe reading through the wiki a couple of times, and  
then trying to run a simulation as described in the getting started  
section just to see how everything fits together.

All that said, welcome to the mailing list and to the Paparazzi community!
--G

On Mon, 15 Nov 2010 17:03:14 -0000, Christian Merfels  
<address@hidden> wrote:

> Hello together,
>
> I'm an engineering student from Lyon who got currently involved in a
> project of building an UAV. We took over the project from another group,
> which already put some work in this. Right now, some hardware was
> already bought:
> - a microcontroller (PIC16F876A, 20Mhz)
> - a receiver/transmitter set (ARM-U8, frequence 868Mhz)
> - a GPS chip (EM406A)
> - a quartz (20Mhz)
> - a gyroscope (IDG 500Dual)
> - a batterie
> - some cables
>
> (As we think that the receiver/transmitter doesn't work with Paparazzi
> (?), we are probably going to change them.)
>
> Our goal is to buy a Twinstar II, build the necessairy card, wire
> everything together and than control the drone from the ground via
> Paparazzi.
>
> Now as I have described the setting, do you guys think this is possible?
> I'm not quite sure about the true function and work done by Paparazzi;
> am I correct when I say:
> * Paparazzi does all the aerodynamics calculation
> * It than sends the current speed and direction orders to the plane
> * The card on the plane needs to interpretate the orders and do the
> actual adjustments of control signals / power levels
> * The plane itself sends back GPS / gyroscop signals to Paparazzi
>
> So our main work would come down to the above described interpretation
> of orders. Is our microcontroller sufficient for this?
>
> I'm sorry for this quite lengthly explanation, but I tried to keep it
> short anyways :-). When reading the Paparazzi Wiki, talking to the old
> group and our tutor, we got a lot of different infos about Paparazzi's
> mode of operation + capabilities, so we thought it would be the best to
> ask you guys directly.
>
> Best regards,
> Christian
>
> _______________________________________________
> Paparazzi-devel mailing list
> address@hidden
> http://lists.nongnu.org/mailman/listinfo/paparazzi-devel


--
Using Opera's revolutionary email client: http://www.opera.com/mail/