Re: [Paparazzi-devel] Futaba TC7

[Árni Þorvaldsson]

Thanks, already tried to change blocks and it doesn´t work, its stopped at 
holding point and I can´t move to next block. I will check wiring and try to 
get the communication working.

regards Arni
________________________________
Frá: address@hidden address@hidden fyrir hönd Felix Ruess address@hidden
Sent: 25. júlí 2012 11:12
To: address@hidden
Efni: Re: [Paparazzi-devel] Futaba TC7

You can also enable the debug fbw telemetry mode via

<define name="TELEMETRY_MODE_FBW" value="1"/>.

as described at 
http://paparazzi.enac.fr/wiki/Radio_Control#Measuring_the_PPM_time_values

On Wed, Jul 25, 2012 at 12:50 PM, Christoph Niemann 
<address@hidden<mailto:address@hidden>> wrote:
Hi Arni,

you could for instance try to change the block in the flightplan, that is 
currently executed. E.g. click on "Standby" and see if the AP switches to 
Standby from wait GPS. Double check your radio configuration and your wiring 
(tx from the ap wired correctly, rx not). You could also try to really wire the 
UART from your ap to the UART of your UART to USB converter. Remember: RX and 
TX crossed :-)
Sort this out first you'll need it to fly, then fix the problem with the radio 
file.

Cheers

Christoph


2012/7/25 Árni Þorvaldsson <address@hidden<mailto:address@hidden>>
Thanks for the reply, changing to debug in GCS doesn´t work!
It seems like my datalink is not working both ways, I just tested outside to 
see if I could set it to auto1 or 2 from GCS and it did not work either. So I 
think that I have to fix the datalink first.
Have others encountered this problem? I am not sure how to tackle this.

kind regards Arni.
________________________________
Frá: address@hidden<mailto:address@hidden> 
address@hidden<mailto:address@hidden>] fyrir hönd Felix Ruess 
address@hidden<mailto:address@hidden>]
Sent: 25. júlí 2012 07:10
To: address@hidden<mailto:address@hidden>
Efni: Re: [Paparazzi-devel] Futaba TC7

See http://paparazzi.enac.fr/wiki/Radio_Control

On Wed, Jul 25, 2012 at 8:58 AM, Christoph Niemann 
<address@hidden<mailto:address@hidden><mailto:address@hidden<mailto:address@hidden>>>
 wrote:
Hi Arni,

you can set the fbw telemetry mode to debug. In this case you get all the 
values from your RC as message. I think the name of the message was "RC". You 
can move the switch then and see, which of the values alters. Knowing this, you 
can edit your radio file and assign mode to the right channel. Be aware that in 
the radio file the order in which the channels are assigned decide, whether it 
is channel number 1 or 2 not the chars.

Cheers

Christoph


2012/7/24 Árni Þorvaldsson 
<address@hidden<mailto:address@hidden><mailto:address@hidden<mailto:address@hidden>>>
Hi
I have the Futaba TC7 together with RS617FS receiver and it´s working fine 
except my 3 position switch. It´s is set on switch on the left side but that 
one is 2 position so I don´t get Auto 1. How can I assign modes (manual, 
auto1,auto2) to the right switch?

regards Arni

_______________________________________________
Paparazzi-devel mailing list
address@hidden<mailto:address@hidden><mailto:address@hidden<mailto:address@hidden>>
https://lists.nongnu.org/mailman/listinfo/paparazzi-devel


_______________________________________________
Paparazzi-devel mailing list
address@hidden<mailto:address@hidden><mailto:address@hidden<mailto:address@hidden>>
https://lists.nongnu.org/mailman/listinfo/paparazzi-devel



_______________________________________________
Paparazzi-devel mailing list
address@hidden<mailto:address@hidden>
https://lists.nongnu.org/mailman/listinfo/paparazzi-devel


_______________________________________________
Paparazzi-devel mailing list
address@hidden<mailto:address@hidden>
https://lists.nongnu.org/mailman/listinfo/paparazzi-devel