Re: [Paparazzi-devel] Baro_ms5611

[Árni Þorvaldsson]

Hi Felix and thanks for your reply,
 I don´t get any errors but the messages from the baro sensor is not displayed 
in the messages tool.

When I run ./paparazzi_version it doesn´t work
address@hidden:~/paparazzi$ ./paparazzi_version
bash: ./paparazzi_version: No such file or directory

But here is my configuration part of my airframe.

<!DOCTYPE airframe SYSTEM "airframe.dtd">


<airframe name="Funjet Tiny 2.11">

  <firmware name="fixedwing">
    <define name="AGR_CLIMB"/>
    <define name="USE_AIRSPEED"/>
    <define name="SENSOR_SYNC_SEND"/>
    <define name="LOITER_TRIM"/>
    <define name="ALT_KALMAN"/>

    <target name="sim"             board="pc"/>

    <target name="ap"             board="tiny_2.11">
    </target>

    <subsystem name="radio_control" type="ppm"/>
    <subsystem name="joystick"/>

    <!-- Communication -->
    <subsystem name="telemetry" type="transparent"/>
    <subsystem name="imu" type="ppzuav"/>


    <!-- Actuators are automatically chosen according to board-->
    <subsystem name="control"/>
    <!-- Sensors -->
    <subsystem name="ahrs" type="float_dcm"/>
    <subsystem name="gps"             type="ublox"/>

    <subsystem name="navigation"/>
    <!-- Interfaces -->
    <subsystem name="i2c"/>

  </firmware>

  <modules>
    <load name="infrared_adc.xml"/>
    <load name="humid_sht.xml"/>
    <load name="airspeed_ets.xml"/>
    <load name="temp_temod.xml"/>
    <load name="baro_ms5611_i2c.xml"/>
  </modules>

  <firmware name="setup">
    <target name="tunnel"             board="tiny_2.11"/>
    <target name="setup_actuators"     board="tiny_2.11"/>
  </firmware>

________________________________
Frá: address@hidden address@hidden fyrir hönd Felix Ruess address@hidden
Sent: 9. janúar 2013 18:49
To: Paparazzi devel list
Efni: Re: [Paparazzi-devel] Baro_ms5611

Hi Arni,

could you please provide some more details? What version, post your config, 
post the actual error, etc...
And please when reporting problems always run ./paparazzi_version in your 
paparazzi dir and include that version number in the mail.

Cheers, Felix


On Wed, Jan 9, 2013 at 11:21 AM, Árni Þorvaldsson 
<address@hidden<mailto:address@hidden>> wrote:
hello all
I am trying to get sensors to work through I2C port on Tiny 2.11. I already got 
the airspeed ets sensor to work properly but now I am trying to add Baro MS5611 
and I am not receiving any messages from him.

the wiring is:
VDD-5V
GND-GND
SDI/SDA-SDA
SCLK-SCL

In the airframe file I insert baro_ms5611_i2c module

 At first I got an error so in ap_downlink.h I inserted this:

#ifdef USE_BARO_MS5611_I2C
#include "baro_MS5611_i2c.h"
#define PERIODIC_SEND_BARO_MS5611_I2C(_chan) 
DOWNLINK_SEND_BARO_MS5611_I2C(_chan, &baro_MS5611_I2C_pressure, 
&baro_MS5611_I2C_temp, &baro_MS5511_I2C_z)
#else
#define PERIODIC_SEND_BARO_MS5611_I2C(_chan) {}
#endif

Is there anything I am missing. The address is not the same as the airspeed 
sensor so it should be fine.


best regards
Arni Th

_______________________________________________
Paparazzi-devel mailing list
address@hidden<mailto:address@hidden>
https://lists.nongnu.org/mailman/listinfo/paparazzi-devel