Re: [Paparazzi-devel] Baro MS5611-01BA01

[Avinash Rao]

Hi Arni,

The datasheet says you need to pull the protocol select pin PS high to put it 
into I2C mode rather than SPI. Have you done this? You didn't mention it in 
your wiring description.

Regards,

Avinash.

______________________
Avinash Rao
+(64) 27 429 1159
_______________________


On 6/02/2013, at 9:34, Árni Þorvaldsson <address@hidden> wrote:

> Hi sorry my mistake, the version is Paparazzi version v4.9_devel-419-gc2d60af
> I got the sensors from http://sander-electronic.de/be00067.html
> 
> How do I check if the adress is correct?
> 
> Regards Arni
> ________________________________
> Frá: address@hidden address@hidden fyrir hönd Eduardo lavratti address@hidden
> Sent: 5. febrúar 2013 20:19
> To: Paparazzi developer forum
> Efni: Re: [Paparazzi-devel] Baro MS5611-01BA01
> 
> first of all,  where you get your sensor ?
> The address used are correct ?
> 
> second, i think you pass the version of GIT program not the version of REPO
> 
>> From: address@hidden
>> To: address@hidden
>> Date: Tue, 5 Feb 2013 18:06:44 +0000
>> Subject: [Paparazzi-devel] Baro MS5611-01BA01
>> 
>> Hi
>> I am still trying to get messages from my baro without any luck.
>> My git version 1.7.9.5
>> I am only trying to get the messages from the sensor displayed in messages 
>> tool (not use it during the flight). I don't get any errors, just no message 
>> from the sensor.
>> my wiring is as follow:
>> vdd-5v
>> gnd-gnd
>> SDI/SDA-SDA
>> SCLK-SCL
>> 
>> If anyone has an idea what to try to fix this, please tell me:)
>> 
>> Here is my firmware part:
>> 
>> <!DOCTYPE airframe SYSTEM "airframe.dtd">
>> 
>> <airframe name="Funjet Tiny 2.11">
>> 
>> <firmware name="fixedwing">
>> <define name="SENSOR_SYNC_SEND"/>
>> <define name="USE_AIRSPEED"/>
>> <target name="sim" board="pc"/>
>> 
>> <target name="ap" board="tiny_2.11">
>> <define name="USE_I2C0"/>
>> <define name="USE_I2C1"/>
>> </target>
>> 
>> <subsystem name="radio_control" type="ppm"/>
>> <subsystem name="joystick"/>
>> 
>> <!-- Communication -->
>> <subsystem name="telemetry" type="transparent"/>
>> <subsystem name="imu" type="ppzuav"/>
>> 
>> 
>> <!-- Actuators are automatically chosen according to board-->
>> <subsystem name="control"/>
>> <!-- Sensors -->
>> <subsystem name="ahrs" type="float_dcm"/>
>> <subsystem name="gps" type="ublox"/>
>> <subsystem name="ins" type="alt_float"/>
>> <subsystem name="navigation"/>
>> 
>> 
>> </firmware>
>> 
>> <modules>
>> <load name="infrared_adc.xml"/>
>> <load name="baro_ms5611_i2c.xml"/>
>> <load name="airspeed_ets.xml"/>
>> </modules>
>> 
>> <firmware name="setup">
>> <target name="tunnel" board="tiny_2.11"/>
>> <target name="setup_actuators" board="tiny_2.11"/>
>> </firmware>
>> 
>> 
>> regards Arni
>> 
>> _______________________________________________
>> Paparazzi-devel mailing list
>> address@hidden
>> https://lists.nongnu.org/mailman/listinfo/paparazzi-devel
> 
> _______________________________________________
> Paparazzi-devel mailing list
> address@hidden
> https://lists.nongnu.org/mailman/listinfo/paparazzi-devel