paparazzi-devel
[Top][All Lists]
Advanced

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: [Paparazzi-devel] Using a digital still image camera with Lisa/M


From: Jorn Anke
Subject: Re: [Paparazzi-devel] Using a digital still image camera with Lisa/M
Date: Sun, 24 Nov 2013 00:14:07 +0100

See sw/airborne/boards/lisa_m_2.0.h for defined LEDs

Thanks, didn't see that before. Hopefully I will figure the the rest from here.

However the digital_cam.xml should be rewritten to not use this LED hack and instead directly use gpio_setup_output, gpio_set and gpio_clear.

Hmm, almost like: 


:-) 

Jorn

Date: Sat, 23 Nov 2013 23:27:46 +0100
From: address@hidden
To: address@hidden
Subject: Re: [Paparazzi-devel] Using a digital still image camera with Lisa/M

See sw/airborne/boards/lisa_m_2.0.h for defined LEDs.

However the digital_cam.xml should be rewritten to not use this LED hack and instead directly use gpio_setup_output, gpio_set and gpio_clear.

Cheers, Felix


On Sat, Nov 23, 2013 at 10:57 PM, Jorn Anke <address@hidden> wrote:
As I remember it, on the YAPA board the "led's" in this context were to be regarded as virtual representations of actual pins/connectors on the board.

On my Lisa/M, all the connectors are free (except the uart's which are used to connect gps and xbee), so I guess the answer is any led representing one of the other connections(?)

Jørn


From: address@hidden
To: address@hidden
Date: Sat, 23 Nov 2013 19:40:50 -0200
Subject: Re: [Paparazzi-devel] Using a digital still image camera with Lisa/M


what lisa_m led you like to use to control the cam ?


From: address@hidden
To: address@hidden
Date: Sat, 23 Nov 2013 22:15:21 +0100
Subject: [Paparazzi-devel] Using a digital still image camera with Lisa/M

Hi,

A while ago I configured an YAPA board to trigger a CHDK enabled Canon camera; http://lists.nongnu.org/archive/html/paparazzi-devel/2012-09/msg00196.html

The settings I used in the airframe-file for the YAPA was:

  <modules>
    ...
    <load     name = "digital_cam.xml">
      <define name = "DC_SHUTTER_LED"      value = "7"/>
      <define name = "LED_7_BANK"               value = "0"/>
      <define name = "LED_7_PIN"                   value = "22"/>
      <define name = "USE_LED_7"                  value = "1"/>
      <define name = "DC_RELEASE"               value = "LED_ON"/>    <!-- zero volt on startup -->
      <define name = "DC_PUSH"                    value = "LED_OFF"/>   <!-- 3.3 volt to trigger -->
      <define name = "DC_SHUTTER_DELAY"  value = "4" unit = "quarter_second"/>
      <define name = "SENSOR_SYNC_SEND" value = "1"/>
    </load>
  </modules>

Now I want to do the same with a Lisa/M. I have browsed through the wiki and the mailing-list archive, but have still not found exactly which settings to use for this board.

Anyone who have can share settings/details -or hints for how to use Lisa/M with a CHDK enabled camera?
(Found this related thread: http://lists.nongnu.org/archive/html/paparazzi-devel/2012-11/msg00015.html )


Cheers, Jørn

_______________________________________________ Paparazzi-devel mailing list address@hidden https://lists.nongnu.org/mailman/listinfo/paparazzi-devel

_______________________________________________ Paparazzi-devel mailing list address@hidden https://lists.nongnu.org/mailman/listinfo/paparazzi-devel

_______________________________________________
Paparazzi-devel mailing list
address@hidden
https://lists.nongnu.org/mailman/listinfo/paparazzi-devel



_______________________________________________ Paparazzi-devel mailing list address@hidden https://lists.nongnu.org/mailman/listinfo/paparazzi-devel

reply via email to

[Prev in Thread] Current Thread [Next in Thread]