paparazzi-devel
[Top][All Lists]
Advanced

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: [Paparazzi-devel] Re First release candidate for next v5.8_stable re


From: Bouwens.Mehl
Subject: Re: [Paparazzi-devel] Re First release candidate for next v5.8_stable release Naze32
Date: Sun, 13 Dec 2015 10:52:52 +0100
User-agent: Mozilla/5.0 (Windows NT 6.3; WOW64; rv:38.0) Gecko/20100101 Thunderbird/38.4.0

hi heinrich,

there are no differences for the pinning on the variants you mentioned.
the earlier afro-mini has an offset for the output pins.
for this model i add:
    // afro mini
    featureSet(FEATURE_SERVO_TILT);

this is the only difference in pinning.

cheers
robert

Am 13.12.2015 um 01:10 schrieb Prof. Dr.-Ing. Heinrich Warmers:
Hi Felix,
Tank you and the hole Paparazzi Team for porting the Naze32.
I made joust a bench test with Flyduno MW32  ( A 1:1 copy of AbuseMark Naze32) .

With the original software i use The pins 31 USART1_RX and 29 USART1_TX for telemetry and connection to the laptop with the usb_  bridge CP2102. If the usb-connector is unused the usb_bridge has no power and it seems that is possible to connect  the telemetry radio module. I flow this for over one year.  Perhaps the TX-pin is in the high impedance state. I disconnect the radio telemetry connector before connecting the USB. 
After comment out the spectrum UARTs  i was able to send and receive messages.

For the GPS- connection i use the pins 12 Uart2_TX and 13 UART2_RX.
I use a RC-receiver with sum impulse output connected to RC-CH1 PA0 pin 10  on the Naze32 and baseflight..
For Paparazzi RC_CH6 PA7  is used. The RC is running fine.
For Paparazzi PWM1 PA8 and PWM2 PA11 are dead.
PWM3 PB6, PWM4 PB7, PWM5 PB8 and   PWM6 PB9 have servo impulses.

It seems that there are differences between the Flip32 and the Naze32 in the lay out of the pinning?

Regards

Heinrich









Am 07.12.2015 14:15, schrieb Felix Ruess:
Hi all,

we just tagged the first release candidate for the next stable release as v5.7.0_testing.
Check out the v5.7 or master branch.

With contributions from over 20 people, we fixed a lot of bugs, improved things here and there and have quite a few major additions compared to v5.6.

Just to pick out a few:
- ADS-B support
- improved use of optic flow for velocity estimation
- improved mavlink support
- possibility to reduce RAM and Flash usage by compressing sine table
- hence support for naze32, CC3D and CJMCU boards
- flip mode for multicopters
- INDI guidance loop
- lots of improvements/additions for computer vision modules
- high speed logging to SD Card via SPI
- improve support for Bebop and add Bebop2

Please see the CHANGELOG for a more detailed list of changes and new features.

Cheers,
Felix for the Paparazzi UAV team


_______________________________________________
Paparazzi-devel mailing list
address@hidden
https://lists.nongnu.org/mailman/listinfo/paparazzi-devel



_______________________________________________
Paparazzi-devel mailing list
address@hidden
https://lists.nongnu.org/mailman/listinfo/paparazzi-devel


reply via email to

[Prev in Thread] Current Thread [Next in Thread]