[Top][All Lists]

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

Re: [Paparazzi-devel] STM32 and GPS reception.

From: Pascal Fust
Subject: Re: [Paparazzi-devel] STM32 and GPS reception.
Date: Tue, 3 Jan 2017 21:53:34 +0100

Hi everybody,

I'm gonna add my 5 cents, as I was recently testing different arrangements with a KroozSD and a new Drotek Neo-M8N. 
After trying to get fixes with a Neo-M6 without much success, I was so surprised about the improvement by the new u-blox GPS module. The identical arrangement resulted in fast and precise fixes. 
On my tricopter, I could even put the GPS just on top of the FC, using the GPS shield from Drotek, and I got perfect GPS readings. 
In my new fix-wing aircraft, however, I experienced interference of the FC with the GPS at close distance without the shield. Moving the GPS ~30 centimeters away from the FC solved all GPS problems. The proximity of the (433MHz) telemetry module did not cause any trouble so far.

Regards, Pascal 


2017-01-03 21:20 GMT+01:00 Prof. Dr.-Ing. Heinrich Warmers <address@hidden>:
Hi Helge,
i think the helix antenna must be in the vertical position.
The antenna is to near to the telemetry antenna.
Please put the telemetry module  near the in the ventilation hole in  the back side of the fuselage.
This is better for the RC-reciever as for the GPS-module.
The transceiver Antenna has to be  much away as possible  from the receiver antennas GPS- and RC- receivers.

regards Heinrich

Am 03.01.2017 18:57, schrieb Helge Walle:
Thank you for your kind reply and good advice, Heinrich.

On the attached photo, the location of the autopilot is not easy to change. But this is a project under construction and all the other paparazzi components can be moved to other locations in the plane.

The RC receiver is placed 2-3cm in front of the Lisa/M. And the XBee is approx 8-9cm in front of the RC receiver. Opinions on this are very welcome.

The wiring shown is not permanent, and things look a bit messy at the moment  :-|

If I lengthen the GPS cable I can make room for the unit at the front of the vehicle. Maybe it will help... and I have some ferrite rings that I can use. But I want to test this before I cut into the foam.

Still, not knowing for certain the origin of the noise, and whether it is carried by wire or through air, is a bit frustrating. I tried some measurements with my 50MHz oscilloscope, but could not reveal anything useful.

To try and get more knowledge about how the noise is transmitted, I would like to make a galvanic isolated link between the GPS and the board (for testing only). The easiest way to achieve this (i think) is to use opto isolators for RX and TX, and, a separate battery for the GPS.


2017-01-03 10:32 GMT+01:00 Prof. Dr.-Ing. Heinrich Warmers <address@hidden>:

Hi Helge Walle,

we know at a long time period that the STM32 has much more  noise than the LPC2148.
The periphery on the LPC2148 works only with 8MHz the core with 60 MHz.
Therefore we fly the wing aircraft only with the old Twog and Tiny13.
The Tiny13 is the best but has an old GPS module.
With the NARZE 32  (STM32103) i hat many problems wit the GPS  I get only a fix when i use a lage distance 40cm away from the autopilot pcb.
Try the following:
 1. use ferrite rings for all wires from and to the autopilot PCB.
 2. capsule the autopilot  with aluminium film
 3. keep the GPS module far away from the telemetrie antenna and the motor electronic.
 4. If you use plan antenna keep a balsa wood plate covert with aluminium film under the GPS module (after that we hat 3dB more).
 5. Use a GPS module with active filter between the antenna an the receiver. A club member  make   a new  GPS module with   the Neo8  and a filter an had often an error below 1m. 

The last point use a lower periphery clock for the STM32. This take a lot of work.
If you have 6 satellite revived (38dB and more)  there is no problem in Norway.

Please send me photos of you aircraft and the wireing.

regards Heinrich


Am 02.01.2017 18:17, schrieb Helge Walle:
Hello paparazzi community, and happy new year!

Lately I have been trying to get a satisfactory GPS reception with my STM32 based autopilots, but without success. The two STM32 based boards I have, are a Lisa/M v2.0 and one Elle0. In addition I have an old Twog (LPC2148) to compare with. I have three different GPS's from different vendors, all Ublox5 or Ublox6. The one used most for testing is an Ublox5 receiver with Sarantel antenna (bought from PPZUAV).

I am not sure if the reception quality is influenced by me living 62 degrees north (Norway).

When I connect my GPS receivers to either the Twog or my PC, the fix happens very quickly, and I get approx 6m accuracy outdoors. And, most important, the results are consistent.

When I connect the same GPS's to the STM32 boards, the reception is noticeably worse, not consistent, and it may take several minutes to get a fix, even outdoors.

I tried longer leads, up to 1m. Reception got better, but by far not as good as with the Twog or a PC. Also I tried ferrite rings with better, but not good results. Longer leads combined with ferrite rings brought things close to ok. But then again my plane is small...

I am planning on connecting the GPS via an optical coupler, or even try a wireless connection to see if the interference is reduced. This would anyway be just for testing because of the added complexity. I am not sure if the interference is carried through the connection leads, or via air or both. Does anyone know this?

Searching the net, I found a forum where it was claimed that the interference has something to do with cyclic reading of the STM32 flash. However I cannot confirm this myself.

Shielding of the board is something I hesitate to try, because it makes everything more difficult when connecting and disconnecthing peripherals.

Before I continue with this, does anyone have any knowledge that would help? There is a thread on the mailing list from 2012, but I couldn't find anything very helpful there.

Are there any settings on the STM32F1/4 that could be helpful in reducing the noise?


Paparazzi-devel mailing list

Paparazzi-devel mailing list

Paparazzi-devel mailing list

Paparazzi-devel mailing list

reply via email to

[Prev in Thread] Current Thread [Next in Thread]