qemu-devel
[Top][All Lists]
Advanced

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

[Qemu-devel] [PATCH v4 08/10] block: add backing-file option to block-st


From: Jeff Cody
Subject: [Qemu-devel] [PATCH v4 08/10] block: add backing-file option to block-stream
Date: Wed, 4 Jun 2014 09:51:10 -0400

On some image chains, QEMU may not always be able to resolve the
filenames properly, when updating the backing file of an image
after a block job.

For instance, certain relative pathnames may fail, or drives may
have been specified originally by file descriptor (e.g. /dev/fd/???),
or a relative protocol pathname may have been used.

In these instances, QEMU may lack the information to be able to make
the correct choice, but the user or management layer most likely does
have that knowledge.

With this extension to the block-stream api, the user is able to change
the backing file of the active layer as part of the block-stream
operation.

This allows the change to be 'safe', in the sense that if the attempt
to write the active image metadata fails, then the block-stream
operation returns failure, without disrupting the guest.

If a backing file string is not specified in the command, the backing
file string to use is determined in the same manner as it was
previously.

Reviewed-by: Eric Blake <address@hidden>
Signed-off-by: Jeff Cody <address@hidden>
---
 block/stream.c   | 11 +++++------
 blockdev.c       | 12 ++++++++++++
 hmp.c            |  3 ++-
 qapi-schema.json | 18 +++++++++++++++++-
 qmp-commands.hx  |  2 +-
 5 files changed, 37 insertions(+), 9 deletions(-)

diff --git a/block/stream.c b/block/stream.c
index 91d18a2..1c7f0a0 100644
--- a/block/stream.c
+++ b/block/stream.c
@@ -32,7 +32,7 @@ typedef struct StreamBlockJob {
     RateLimit limit;
     BlockDriverState *base;
     BlockdevOnError on_error;
-    char backing_file_id[1024];
+    char *backing_file_str;
 } StreamBlockJob;
 
 static int coroutine_fn stream_populate(BlockDriverState *bs,
@@ -186,7 +186,7 @@ wait:
     if (!block_job_is_cancelled(&s->common) && sector_num == end && ret == 0) {
         const char *base_id = NULL, *base_fmt = NULL;
         if (base) {
-            base_id = s->backing_file_id;
+            base_id = s->backing_file_str;
             if (base->drv) {
                 base_fmt = base->drv->format_name;
             }
@@ -196,6 +196,7 @@ wait:
     }
 
     qemu_vfree(buf);
+    g_free(s->backing_file_str);
     block_job_completed(&s->common, ret);
 }
 
@@ -217,7 +218,7 @@ static const BlockJobDriver stream_job_driver = {
 };
 
 void stream_start(BlockDriverState *bs, BlockDriverState *base,
-                  const char *base_id, int64_t speed,
+                  const char *backing_file_str, int64_t speed,
                   BlockdevOnError on_error,
                   BlockDriverCompletionFunc *cb,
                   void *opaque, Error **errp)
@@ -237,9 +238,7 @@ void stream_start(BlockDriverState *bs, BlockDriverState 
*base,
     }
 
     s->base = base;
-    if (base_id) {
-        pstrcpy(s->backing_file_id, sizeof(s->backing_file_id), base_id);
-    }
+    s->backing_file_str = g_strdup(backing_file_str);
 
     s->on_error = on_error;
     s->common.co = qemu_coroutine_create(stream_run);
diff --git a/blockdev.c b/blockdev.c
index 16b44f7..23a76eb 100644
--- a/blockdev.c
+++ b/blockdev.c
@@ -1875,6 +1875,7 @@ static void block_job_cb(void *opaque, int ret)
 void qmp_block_stream(const char *device,
                       bool has_base, const char *base,
                       bool has_base_node_name, const char *base_node_name,
+                      bool has_backing_file, const char *backing_file,
                       bool has_speed, int64_t speed,
                       bool has_on_error, BlockdevOnError on_error,
                       Error **errp)
@@ -1926,6 +1927,9 @@ void qmp_block_stream(const char *device,
         return;
     }
 
+    /* backing_file string overrides base bs filename */
+    base_name = has_backing_file ? backing_file : base_name;
+
     /* Verify that 'base' is in the same chain as 'bs', if 'base' was
      * specified */
     if (base_bs && !bdrv_chain_contains(bs, base_bs)) {
@@ -1933,6 +1937,14 @@ void qmp_block_stream(const char *device,
         return;
     }
 
+    /* if we are streaming the entire chain, the result will have no backing
+     * file, and specifying one is therefore an error */
+    if (base_bs == NULL && has_backing_file) {
+        error_setg(errp, "backing file specified, but streaming the "
+                         "entire chain");
+        return;
+    }
+
     stream_start(bs, base_bs, base_name, has_speed ? speed : 0,
                  on_error, block_job_cb, bs, &local_err);
     if (local_err) {
diff --git a/hmp.c b/hmp.c
index bb934df..644e854 100644
--- a/hmp.c
+++ b/hmp.c
@@ -1173,7 +1173,8 @@ void hmp_block_stream(Monitor *mon, const QDict *qdict)
     int64_t speed = qdict_get_try_int(qdict, "speed", 0);
 
     qmp_block_stream(device, base != NULL, base,
-                     false, NULL, qdict_haskey(qdict, "speed"), speed,
+                     false, NULL, false, NULL,
+                     qdict_haskey(qdict, "speed"), speed,
                      true, BLOCKDEV_ON_ERROR_REPORT, &error);
 
     hmp_handle_error(mon, &error);
diff --git a/qapi-schema.json b/qapi-schema.json
index 2cdd96e..3400561 100644
--- a/qapi-schema.json
+++ b/qapi-schema.json
@@ -2611,6 +2611,21 @@
 # @base-node-name: #optional the block driver state node name of the
 #                            common backing file.  (Since 2.1)
 #
+# @backing-file: #optional The backing file string to write into the active
+#                          layer. This filename is not validated.
+#
+#                          If a pathname string is such that it cannot be
+#                          resolved by QEMU, that means that subsequent QMP or
+#                          HMP commands must use node-names for the image in
+#                          question, as filename lookup methods will fail.
+#
+#                          If not specified, QEMU will automatically determine
+#                          the backing file string to use, or error out if 
there
+#                          is no obvious choice.  Care should be taken when
+#                          specifying the string, to specify a valid filename 
or
+#                          protocol.
+#                          (Since 2.1)
+#
 # @speed:  #optional the maximum speed, in bytes per second
 #
 # @on-error: #optional the action to take on an error (default report).
@@ -2624,7 +2639,8 @@
 ##
 { 'command': 'block-stream',
   'data': { 'device': 'str', '*base': 'str', '*base-node-name': 'str',
-            '*speed': 'int', '*on-error': 'BlockdevOnError' } }
+            '*backing-file': 'str', '*speed': 'int',
+            '*on-error': 'BlockdevOnError' } }
 
 ##
 # @block-job-set-speed:
diff --git a/qmp-commands.hx b/qmp-commands.hx
index 9ddc39a..b41af0f 100644
--- a/qmp-commands.hx
+++ b/qmp-commands.hx
@@ -979,7 +979,7 @@ EQMP
 
     {
         .name       = "block-stream",
-        .args_type  = 
"device:B,base:s?,base-node-name:s?,speed:o?,on-error:s?",
+        .args_type  = 
"device:B,base:s?,base-node-name:s?,speed:o?,backing-file:s?,on-error:s?",
         .mhandler.cmd_new = qmp_marshal_input_block_stream,
     },
 
-- 
1.9.3




reply via email to

[Prev in Thread] Current Thread [Next in Thread]