[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
[PATCH 2/2] hppa: Fix serial port pass-through
From: |
Helge Deller |
Subject: |
[PATCH 2/2] hppa: Fix serial port pass-through |
Date: |
Thu, 26 May 2022 13:19:26 +0200 |
This fixes the serial ports in the emulation to behave as on original
hardware.
On the real hardware, the LASI UART is serial port #0 and the DINO UART
is serial port #1. This is fixed in SEABIOS_HPPA_VERSION >= 6, which is
why the latest firmware is required.
The serial port addresses in hppa/hppa_hardware.h are swapped and the
file is synced with the version in SeaBIOS-hppa. Please note that this
file is shared between qemu and SeaBIOS-hppa, which is why a comment was
added at the top of the file.
When creating the virtual serial ports the correct port addresses are
now used.
Finally, this patch now allows the user to give:
-serial mon:stdio -serial /dev/ttyS4
to use emulated ttyS0 in the guest for console output, and pass ttyS4
from the host to ttyS1 in the guest.
Signed-off-by: Helge Deller <deller@gmx.de>
---
hw/hppa/hppa_hardware.h | 10 ++++++++--
hw/hppa/machine.c | 17 +++++++----------
2 files changed, 15 insertions(+), 12 deletions(-)
diff --git a/hw/hppa/hppa_hardware.h b/hw/hppa/hppa_hardware.h
index 8b6b9222cb..c036d467f3 100644
--- a/hw/hppa/hppa_hardware.h
+++ b/hw/hppa/hppa_hardware.h
@@ -1,4 +1,5 @@
/* HPPA cores and system support chips. */
+/* Be aware: This file is shared as-is with seabios-hppa. */
#ifndef HW_HPPA_HPPA_HARDWARE_H
#define HW_HPPA_HPPA_HARDWARE_H
@@ -30,13 +31,18 @@
#define PCI_HPA DINO_HPA /* PCI bus */
#define IDE_HPA 0xf9000000 /* Boot disc controller */
+/* offsets to DINO HPA: */
+#define DINO_PCI_ADDR 0x064
+#define DINO_CONFIG_DATA 0x068
+#define DINO_IO_DATA 0x06c
+
#define PORT_PCI_CMD (PCI_HPA + DINO_PCI_ADDR)
#define PORT_PCI_DATA (PCI_HPA + DINO_CONFIG_DATA)
#define FW_CFG_IO_BASE 0xfffa0000
-#define PORT_SERIAL1 (DINO_UART_HPA + 0x800)
-#define PORT_SERIAL2 (LASI_UART_HPA + 0x800)
+#define PORT_SERIAL1 (LASI_UART_HPA + 0x800)
+#define PORT_SERIAL2 (DINO_UART_HPA + 0x800)
#define HPPA_MAX_CPUS 16 /* max. number of SMP CPUs */
#define CPU_CLOCK_MHZ 250 /* emulate a 250 MHz CPU */
diff --git a/hw/hppa/machine.c b/hw/hppa/machine.c
index d1e174b1f4..5d23b9e528 100644
--- a/hw/hppa/machine.c
+++ b/hw/hppa/machine.c
@@ -32,7 +32,7 @@
#define MAX_IDE_BUS 2
-#define MIN_SEABIOS_HPPA_VERSION 1 /* require at least this fw version */
+#define MIN_SEABIOS_HPPA_VERSION 6 /* require at least this fw version */
#define HPA_POWER_BUTTON (FIRMWARE_END - 0x10)
@@ -236,18 +236,15 @@ static void machine_hppa_init(MachineState *machine)
/* Realtime clock, used by firmware for PDC_TOD call. */
mc146818_rtc_init(isa_bus, 2000, NULL);
- /* Serial code setup. */
+ /* Serial ports - Lasi and Dino use a 7.272727 MHz clock. */
if (serial_hd(0)) {
- uint32_t addr = DINO_UART_HPA + 0x800;
- serial_mm_init(addr_space, addr, 0,
- qdev_get_gpio_in(dino_dev, DINO_IRQ_RS232INT),
- 115200, serial_hd(0), DEVICE_BIG_ENDIAN);
+ serial_mm_init(addr_space, LASI_UART_HPA + 0x800, 0,
+ qdev_get_gpio_in(lasi_dev, LASI_IRQ_UART_HPA), 7272727 / 16,
+ serial_hd(0), DEVICE_BIG_ENDIAN);
}
-
if (serial_hd(1)) {
- /* Serial port */
- serial_mm_init(addr_space, LASI_UART_HPA + 0x800, 0,
- qdev_get_gpio_in(lasi_dev, LASI_IRQ_UART_HPA), 8000000 / 16,
+ serial_mm_init(addr_space, DINO_UART_HPA + 0x800, 0,
+ qdev_get_gpio_in(dino_dev, DINO_IRQ_RS232INT), 7272727 / 16,
serial_hd(1), DEVICE_BIG_ENDIAN);
}
--
2.35.3