> > more details will follow as soon as I find some time...
> Thanks and success with your second group of tests.
>
> Martin
> > best regards and greetings
> > to all fellow GNURadioers
> >
> > vincenzo
> >
> > PS
> > Rafael, just have a look back a this thread and you'll find all the
> > info you need to do your test broadcast. Thanks for your interest
> >
> >
> >
> >
> >
> >
> > 2008/10/31 Martin Dudok van Heel <
address@hidden>
> > Hi Vincenzo.
> > How are things going with your exams.
> >
> > I hope well.
> >
> > Thanks for your help so far.
> >
> > I finally got your DVB-T dump streams working.
> > I first tried using an undersampled basicTX but never got it
> > to work.
> > (use a niquist mirror in the VHF range on channel 11 or 12
> > (219.5 Mhz or 226.5 Mhz))
> >
> > I now use a RFX900 and that works with a pinnacle PCTV-Solo
> > 72e usb DVB-T receiver card plugged into my PC.
> > I use 858.0 Mhz (channel 69)
> > I used a 10 dB attenuator on the antenna output to limit
> > output power.
> > I also modified the RFX900 to enable transmitting outside of
> > the ISM band. (disable saw-filter. add 220 pF capacitor)
> >
> > Apparantly the pinnacle 72e can receive 7 Mhz channels on the
> > UHF channels.
> > My standalone settopbox DVB-T receiver can't handle it.
> >
> > I noticed you don't use the full possible range in your 16 bit
> > streams.
> > (only goes from -80 to +80 while you could use -8192 to 8192)
> > Is this on purpose?
> > I can multiply samples by 64 and get a cleaner signal. (But
> > also more output power)
> >
> >
> > I do have a request, I hope it is not too much work.
> > Could you make a stream with 10 Msamples/sec samplerate and 8
> > Mhz wide channel.
> > This way I can use standard standalone DVB-T receivers and
> > don't have the 7Mhz bandwith on UHF problem.
> >
> > For the 10 Msps stream I would have to use my USRP2 to output
> > it.
> > It has a 100 Mhz DAC (in stead of 64 Msps in the USRP1)
> > It has a gbit ethernet connection for the samples, so I can go
> > up to 25 Msps.
> > It can only do fixed interpolation rates so I have to choose
> > from the table below.
> > (8 Msamples/sec is not supported on the USRP2)
> >
> >
> > USRP2
> > dac_rate interp ethernet_sample_rate
> > 100 4 25
> > 100 5 20
> > 100 6 16.67
> > 100 7 14.29
> > 100 8 12.5
> > 100 9 11.11
> > 100 10 10 <----I think 10 Msamples/sec
> > should be optimal
> > 100 11 9.09
> > 100 12 8.33
> > 100 13 7.69
> > 100 14 7.14
> >
> >
> > I think 10 Msamples/sec would be a good candidate.
> >
> > Have you also tried using 8 Msamples/sec on the USRP1?
> > I know there would be no room left for IF channel filtering,
> > but it could in theory still work.
> > If this works I would also very much appreciate a 8Mhz
> > bandwidth stream with 8 MSPS samplerate so I can demonstrate
> > with a standard USRP1.
> >
> > Thanks for your help so far.
> > I appreciate it very much.
> >
> > And good luck with your exams.
> >
> > Have a nice weekend.
> >
> > Greetings,
> > Martin
> >
> >
> >
> >
> > --
> > Vincenzo Pellegrini