[Top][All Lists]
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
Re: [fluid-dev] M2496 M-audio
From: |
Dave Serls |
Subject: |
Re: [fluid-dev] M2496 M-audio |
Date: |
Wed, 11 May 2005 14:06:13 -0600 |
On Wed, 11 May 2005 13:57:29 -0600
Garett Shulman <address@hidden> wrote:
> I can let you know the asoundrc I use for fluid and ice1712 later this
> evening. Also, there are some examples here:
> http://alsa.opensrc.org/index.php?page=1712+.asoundrc
> and here:
> http://www.alsa-project.org/alsa-doc/doc-php/template.php?module=ice1712#aso
> There is another wiki, but I can't seem to find it.
>
> However, I would try just:
>
> pcm.ice1712 {
> type hw
> card 2
> }
> pcm.fluid_convert {
> type plug
> slave ice1712
> }
>
>
> -Garett
Thanks!
I did get fluidsynth to initialize with:
pcm.fluid_cnv {
type plug
slave {
pcm "hw:2,0"
rate 48000
}
}
Haven't even listened to it yet...
Thanks again and I may owe you a beverage at the Walnut or other location.
>
> Dave Serls wrote:
>
> >On Wed, 11 May 2005 12:02:36 -0600
> >Garett Shulman <address@hidden> wrote:
> >
> >
> >
> >>Hey Dave, the 2496 hardware outs use sample rate of 48000. You need to
> >>either setup a plug device in asoundrc and point fluidsynth at that or
> >>point fluidsynth to plughw:0,0 instead of hw:0,0 (or whatever your card
> >>numbers are).
> >>HTH. -Garett
> >>
> >>Dave Serls wrote:
> >>
> >>
> >>
> >>>I'm trying to test my M-audio 2496 Audiophile with fluidsynth.
> >>>Other cards on this system (Mandrake 10.1, ALSA 1.0.8) work ok.
> >>>The M-Audio appears to want some other format -- I think I have it
> >>>set to 44100 .
> >>>
> >>>The error is:
> >>>fluidsynth: error: Failed to find a workable audio format
> >>>Failed to create the audio driver
> >>>
> >>>Do I need some plugin or .asoundrc entry??
> >>>Thanks for any assistance.
> >>>
> >>>
> >>>
> >>>
> >>>
> >>
> >>
> >
> > Well, I'm trying something like that.
> > I've never seen any decent documentation on this and don't
> > know which end is input here.
> >
> > Now I get 4 messages of "slave PCM not useable" using
> >
> >pcm.ice1712 {
> > type hw
> > card 2
> >}
> >ctl.ice1712 {
> > type hw
> > card 2
> >}
> >pcm_slave.cnv {
> > pcm ice1712
> > format S24_LE
> > channels 2
> > rate 48000
> >}
> >pcm.fluid_convert {
> > type plug
> > slave cnv
> >}
> >
> >
> > Arrrgh.
> >
> >
> >
> >
>
>
>
> _______________________________________________
> fluid-dev mailing list
> address@hidden
> http://lists.nongnu.org/mailman/listinfo/fluid-dev
>
--
************************************************************************
* Dave Serls Littleton, CO, USA *
* dashs.denver.co.us sorrybiscuit.com *
************************************************************************