Hi Kaleem,
Each USRP has its on reference crystal oscillator. This oscillator may have maximum +/- 50 PPM ( Matt said the new USRPs has maximum 20 PPM) frequency error. Lets assume the error is 10 PPM in each USRP. This means, that at 2500 MHz (2.5 GHz) the error = 2500 * 10 = 25000 Hz = 25KHz.
Now imagine that the first USRP has +25 KHz frequency deviation error and the second one has - 25KHz frequency error. This means + 50 KHz frequency mismtch between your TX and Rx Frequencies. This is probably what is causing this high error rate that you see.
To solve this problem you simply do :
1) Use usrp_siggen.py to send single tone at F1 frequency (For example, use F1 = 2475 MHz) from your TX USRP. The best thing is F1 be the frequency used in your FSK experiments.
2) With your RX USRP, start usrp_fft.py with frequency F1 and
decimation= 128 (or 256). You should see your transmitted tone but may be it's frequency is shifted. Calculate this frequency shift.
3) Add/subtract this frequency shift to your RX USRP frequency tunning function.
4) Now your two USRPs frequency mismatch should not be the problem. If the errors is still there, then you have to search for another reason.
Regards,
Firas
--- On Wed, 7/23/08, kaleem ahmad <address@hidden> wrote:
From: kaleem ahmad <address@hidden>
Subject: Re: [Discuss-gnuradio] FSK with RFX2400
To: address@hidden
Date: Wednesday, July 23, 2008, 5:23 PM
I have just provided the information which can be helpful for you, and the
code is also attached with it and a sample received file is also there along
with actual sent
file.
Please just scroll up and you will find my message with all this
information. Additionally OS is 'openSUSI' a favour of Linux. But if
you
still need some more info then please let me know.
Thaks
Patrick Strasser wrote:
>
> kaleem ahmad wrote am 2008-07-23 11:38:
>> Dear All,
>>
>> Can anyone also address the first part of my question aslo, I mean how
to
>> improve the quality of received data. I mean is it normal with GNU
>> Radio/USRP that we receive so currupt data or I am doing something
wrong.
>> Any suggestion please
>
> Before you wrote
>
>> after using tune
>> to set the proper ferquency I was able to run transmitter and receiver
> > sussfully. I didnt change anything else in the example.
> > The problem is data
>> which I receive is too much corrupt (lot of data
errors)..
>
> Your description is not very exact. You could help us to help you with
> more information:
>
> What is your setup? OS, distribution, used version of packages, GNU
> Radio, hardware setup, used parts (cable, antennas), environment.
> What do you do? Which code do you use?
> What did you change?
> What did you get? Error messages? (add _exact_ transcripts of errors)
> What did you expect?
> Please provide exact information, code should be attached. If you
> changed something, mark the changes so helpers will find it easier.
>
> If you have recorded samples of a good and bad transmissions, send us a
> representative part of it. If you need to show more than a hand full of
> kilobytes, put them on a web server or ftp server and provide a link.
>
> Are you sure to have read the FAQ and introducing documentation?
>
>
Patrick
> --
> Engineers motto: cheap, good, fast: choose any two
> Patrick Strasser <patrick dot strasser at student dot tugraz dot at>
> Student of Telematik, Techn. University Graz, Austria
>
>
>
> _______________________________________________
> Discuss-gnuradio mailing list
> address@hidden
> http://lists.gnu.org/mailman/listinfo/discuss-gnuradio
>
>
--
View this message in context:
http://www.nabble.com/FSK-with-RFX2400-tp18587205p18611871.html
Sent from the GnuRadio mailing list archive at Nabble.com.
_______________________________________________
Discuss-gnuradio mailing list
address@hidden
http://lists.gnu.org/mailman/listinfo/discuss-gnuradio |