problems with 3310

[mspattnaik]

hi all
  first of all thanks to Mr.Bozo for his suggestions to my earlier problem 
postings,sir u have suggested me to change it to m2bus even i have changed it 
in the .gnokiirc file and this time used the latest version (Version 
0.5.0pre6),and the problem remains same i am sending the details of the out put 
i have got,
   $gnokii --monitor
GNOKII Version 0.5.0pre6
Opened configuration file /root/.gnokiirc
Added new section global
Adding key/value port//dev/ttyS0
Adding key/value model/3310
Adding key/value initlength/default
Adding key/value connection/m2bus
Adding key/value bindir//usr/local/sbin/
Adding key/value use_locking/yes
Adding key/value serial_baudrate/19200
Adding key/value smsc_timeout/10
Added new section connect_script
Adding key/value TELEPHONE/12345678
Added new section disconnect_script
phone instance config:
model: 3310
port_device: /dev/ttyS0
connection_type: 7
init_length: 0
serial_baudrate: 19200
serial_write_usleep: -1
hardware_handshake: 0
require_dcd: 0
smsc_timeout: 100
connect_script:
disconnect_script:
Serial device: opening device /dev/ttyS0
Serial device: setting speed to 9600
Serial device: setting RTS to high and DTR to low
Message sent: 0x40 / 0x0004
00 01 64 01                                     |   d
Serial device: setting RTS to low and DTR to low
Serial device: setting RTS to high and DTR to low
SM_Block Retry - 0
Message sent: 0x40 / 0x0004
00 01 64 01                                     |   d
Serial device: setting RTS to low and DTR to low
Serial device: setting RTS to high and DTR to low
SM_Block Retry - 1
Message sent: 0x40 / 0x0004
00 01 64 01                                     |   d
Serial device: setting RTS to low and DTR to low
Serial device: setting RTS to high and DTR to low
SM_Block Retry - 2
Telephone interface init failed: Command timed out. Quitting.

Even i am getting the same out put when i remove the cable from the pc and run 
the gnokii in the command line.
 i have run the statserial in order monitor serial port and below is the output 
before running gnokii
$statserial /dev/ttyS0
 
Device: /dev/ttyS0

Signal  Pin  Pin  Direction  Status  Full
Name    (25) (9)  (computer)         Name
-----   ---  ---  ---------  ------  -----
FG       1    -      -           -   Frame Ground
TxD      2    3      out         -   Transmit Data
RxD      3    2      in          -   Receive  Data
RTS      4    7      out         1   Request To Send
CTS      5    8      in          1   Clear To Send
DSR      6    6      in          0   Data Set Ready
GND      7    5      -           -   Signal Ground
DCD      8    1      in          0   Data Carrier Detect
DTR     20    4      out         1   Data Terminal Ready
RI      22    9      in          0   Ring Indicator

after running the gnokii the output becomes

Device: /dev/ttyS0

Signal  Pin  Pin  Direction  Status  Full
Name    (25) (9)  (computer)         Name
-----   ---  ---  ---------  ------  -----
FG       1    -      -           -   Frame Ground
TxD      2    3      out         -   Transmit Data
RxD      3    2      in          -   Receive  Data
RTS      4    7      out         1   Request To Send
CTS      5    8      in          0   Clear To Send
DSR      6    6      in          0   Data Set Ready
GND      7    5      -           -   Signal Ground
DCD      8    1      in          0   Data Carrier Detect
DTR     20    4      out         0   Data Terminal Ready
RI      22    9      in          0   Ring Indicator

this might be as the output of gnokii shows: 

Serial device: setting RTS to low and DTR to low
Serial device: setting RTS to high and DTR to low

the value of RTS varies to 1 when it is high and to 0 when it is low.kindly 
suggest me in order to fix my problems

 thanking u
 mspattnaik

 
Get Your Private, Free E-mail from Indiatimes at http://email.indiatimes.com

 Buy the best in Movies at http://www.videos.indiatimes.com

Bid for for Air Tickets @ Re.1 on Air Sahara Flights. Just log on to 
http://airsahara.indiatimes.com and Bid Now!