Re: [Ltib] Problem getting started with Microwindows/Nano-X

[rsgrimes]

Oh, I should clarify. In my ltib kernel config, I do see a 240x320 option, but 
no 320x240 option - is this my problem?  If so, how do I fix this?

Is this something in the BSP?

Help!

Bob

Sent from my Verizon Wireless BlackBerry

-----Original Message-----
From: address@hidden

Date: Wed, 18 Mar 2009 01:38:06 
To: Matt Waddel<address@hidden>; <address@hidden>
Subject: Re: [Ltib] Problem getting started with Microwindows/Nano-X


Hi Matt,

I'm using a custom board based quite closely on the Freescale 5329 eval board. 

The symptom you mentioned does seem likely, but I cannot find out where the 
settings are!

No, there is no Help directory in my ltib - which is from a recent CVS grab. 

I can't seem to figure out where to even look!  Any ideas would be greatly 
appreciated!


Bob

Sent from my Verizon Wireless BlackBerry

-----Original Message-----
From: Matt Waddel <address@hidden>

Date: Fri, 13 Mar 2009 09:47:35 
To: <address@hidden>
Subject: Re: [Ltib] Problem getting started with Microwindows/Nano-X



Hi Bob,

Which platform are you using?  There are a couple m68knommu
that have displays and there are 4 different display types supported.
It sounds like the wrong display is selected in the kernel 
configuration.  There is a 240Wx320H and if the last 1/3 of your 
320W x 240H is messed up it may just be a wrong kernel 
configuration.

About the microwindows demos.  Most of the the scripts aren't 
really "executable scripts".  I've had luck just starting them
individually.  Does the BSP you're using have the nanox.html
document in <ltib>/Help/software/?  There are some suggestions
there for some of the nanox demos.

Best regards,
Matt


--- On Thu, 3/12/09, Robert S. Grimes <address@hidden> wrote:

> From: Robert S. Grimes <address@hidden>
> Subject: [Ltib] Problem getting started with Microwindows/Nano-X
> To: address@hidden
> Date: Thursday, March 12, 2009, 7:59 PM
> 
> Hi,
> 
> So, I'm trying to get version 0.90 running on my embedded
> target
> (m68knommu under uClinux).  Everything seems to build
> properly, but
> that's as far as I can get.  I do see a /usr/nanox
> directory on my
> target, with several demo scripts and a bin
> directory.  But none of the
> programs run very well.
> 
> For example, I try the following from /usr/nanox:
> 
>   ./laucher.sh
> 
> This results in the following output on my serial
> terminal:
> 
>   $ ./launcher.sh
>   BIN_FLAT: bad header magic
>   BINFMT_FLAT: bad header magic
>   tsdev (compaq touchscreen emulation) is scheduled
> for removal.
>   See Documentation/feature-removal-schedule.txt for
> details.
>   nxclient: retry connect attempt 1
> 
> and the LCD (320W x 240 H) is interesting: the left 2/3 of
> the screen
> show a matrix of eight icon, presumably representing
> sub-demos (which
> seem to exist in the /usr/nanox/bin directory), seems a
> good start.
> But, the right third of the screen is garbage, and the
> bottom 2-3 lines
> are also garbled across the entire width.  Seems a
> configuration
> problem?
> 
> I couldn't seem to find anything within LTIB to specify the
> correct
> screen configuration for Microwindows, but the framebuffer
>_seems_
> correct, and the Penguin logo is displayed on startup.
> 
> Any ideas?
> 
> Oh, and is this even an issue for here, or is this solely a
> Microwindows
> issue? 
> 
> Thanks!
> -Bob
> 
> 
> 
> 
>_______________________________________________
> LTIB home page: http://bitshrine.org
> 
> Ltib mailing list
> address@hidden
> http://lists.nongnu.org/mailman/listinfo/ltib
> 






_______________________________________________
LTIB home page: http://bitshrine.org

Ltib mailing list
address@hidden
http://lists.nongnu.org/mailman/listinfo/ltib