[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
Re: [avr-chat] how to connect USBasp to attiny2313
From: |
YuGiOhJCJ Mailing-List |
Subject: |
Re: [avr-chat] how to connect USBasp to attiny2313 |
Date: |
Sat, 3 Aug 2013 05:30:48 +0200 |
On Fri, 02 Aug 2013 21:01:45 -0400
Ormund Williams <address@hidden> wrote:
> On Sat, 2013-08-03 at 02:37 +0200, YuGiOhJCJ Mailing-List wrote:
> > I am wondering if I downgrade my avrdude ( to a version before 5.11 ), do
> > you think my old firmware will be compatible with this old version of
> > avrdude ?
> >
> That's another way to go, at long as it supports tiny2313.
>
> Regards.
>
> --
> Ormund
>
>
> _______________________________________________
> AVR-chat mailing list
> address@hidden
> https://lists.nongnu.org/mailman/listinfo/avr-chat
Nice I think I found an old avrdude version for my old programmer firmware:
avrdude 5.2.
$ sudo avrdude -v -B 50 -p t2313 -c usbasp -U flash:w:main.hex
avrdude: Version 5.2, compiled on Aug 3 2013 at 04:39:58
Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/
System wide configuration file is "/usr/etc/avrdude.conf"
User configuration file is "/home/spierre/.avrduderc"
User configuration file does not exist or is not a regular file,
skipping
Using Port : /dev/parport0
Using Programmer : usbasp
Setting bit clk period: 50.0
AVR Part : ATtiny2313
Chip Erase delay : 9000 us
PAGEL : PD4
BS2 : PD6
RESET disposition : possible i/o
RETRY pulse : SCK
serial program mode : yes
parallel program mode : yes
Timeout : 200
StabDelay : 100
CmdexeDelay : 25
SyncLoops : 32
ByteDelay : 0
PollIndex : 3
PollValue : 0x53
Memory Detail :
Block Poll Page
Polled
Memory Type Mode Delay Size Indx Paged Size Size #Pages MinW
MaxW ReadBack
----------- ---- ----- ----- ---- ------ ------ ---- ------ -----
----- ---------
eeprom 65 6 4 0 no 128 4 0 4000
4500 0xff 0xff
flash 65 6 32 0 yes 2048 32 64 4500
4500 0xff 0xff
signature 0 0 0 0 no 3 0 0 0
0 0x00 0x00
lock 0 0 0 0 no 1 0 0 9000
9000 0x00 0x00
lfuse 0 0 0 0 no 1 0 0 9000
9000 0x00 0x00
hfuse 0 0 0 0 no 1 0 0 9000
9000 0x00 0x00
efuse 0 0 0 0 no 1 0 0 9000
9000 0x00 0x00
calibration 0 0 0 0 no 2 0 0 0
0 0x00 0x00
Programmer Type : usbasp
Description : USBasp, http://www.fischl.de/usbasp/
avrdude: error: programm enable: target doesn't answer. 1
avrdude: AVR device initialized and ready to accept instructions
Reading | ################################################## | 100% 0.00s
avrdude: Device signature = 0x000000
avrdude: Yikes! Invalid device signature.
Double check connections and try again, or use -F to override
this check.
avrdude done. Thank you.
But as you can see I got some errors.
Do you see the problem ?
- Re: [avr-chat] how to connect USBasp to attiny2313, (continued)
- Re: [avr-chat] how to connect USBasp to attiny2313, YuGiOhJCJ Mailing-List, 2013/08/02
- Re: [avr-chat] how to connect USBasp to attiny2313, Andreas Graebe, 2013/08/02
- Re: [avr-chat] how to connect USBasp to attiny2313, YuGiOhJCJ Mailing-List, 2013/08/02
- Re: [avr-chat] how to connect USBasp to attiny2313, Ormund Williams, 2013/08/02
- Re: [avr-chat] how to connect USBasp to attiny2313, YuGiOhJCJ Mailing-List, 2013/08/02
- Re: [avr-chat] how to connect USBasp to attiny2313, Ormund Williams, 2013/08/02
- Re: [avr-chat] how to connect USBasp to attiny2313,
YuGiOhJCJ Mailing-List <=
- Re: [avr-chat] how to connect USBasp to attiny2313, Ormund Williams, 2013/08/05
- Re: [avr-chat] how to connect USBasp to attiny2313, YuGiOhJCJ Mailing-List, 2013/08/05
- Re: [avr-chat] how to connect USBasp to attiny2313, Ormund Williams, 2013/08/05
- Re: [avr-chat] how to connect USBasp to attiny2313, YuGiOhJCJ Mailing-List, 2013/08/07
- Re: [avr-chat] how to connect USBasp to attiny2313, Schwichtenberg, Knut, 2013/08/08
- Re: [avr-chat] how to connect USBasp to attiny2313, YuGiOhJCJ Mailing-List, 2013/08/08
- Re: [avr-chat] how to connect USBasp to attiny2313, Ormund Williams, 2013/08/08
- Re: [avr-chat] how to connect USBasp to attiny2313, YuGiOhJCJ, 2013/08/09
- Re: [avr-chat] how to connect USBasp to attiny2313, Ormund Williams, 2013/08/09